Comments (12)
That is the whole purpose of the added RF module.
Unlearn the remote from the itho and add up to 10 remotes to the add-on. Functionality of the remote is at least exactly the same as normal but the result of the remote is now also visible in your domotica system. (in theory you could assign your own functions to the remote but for now you can only change the speed settings for every button)
from ithowifi.
Something worth mentioning:
When I disconnected the power, the blue Itho_status led blinks a few times slow, than fast, than dies.
Reconnecting the power after this moment and the module doesn't work. Not connection to WiFi, not going into AP-mode (standalone).
Disconnecting the power, wait till Itho_status led blinks fast and than reconnect the power, and it works again.
from ithowifi.
Could you send a picture of the itho main pcb? I somehow sounds like the itho firmware is locking up.
When I disconnected the power, the blue Itho_status led blinks a few times slow, than fast, than dies.
That's the itho power supply trickling the last bits of power to the add-on (you might also see the led's on the itho main pcb blinking a few times) After the led is completely off you should wait at least 15 sec or so according to the itho manual before powering on again.
from ithowifi.
Could you send a picture of the itho main pcb? I somehow sounds like the itho firmware is locking up.
That's the itho power supply trickling the last bits of power to the add-on (you might also see the led's on the itho main pcb blinking a few times) After the led is completely off you should wait at least 15 sec or so according to the itho manual before powering on again.
Ah ok, I'm not sure how much time I've waited. I'll keep that in mind next time ;-)
from ithowifi.
And it works, until I use my remote
Is there a difference using the slider on the webinterface or the remote?
Does the itho status led turn on when turning the itho on and does it go off after a few seconds?
from ithowifi.
And it works, until I use my remote
Is there a difference using the slider on the webinterface or the remote?
Does the itho status led turn on when turning the itho on and does it go off after a few seconds?
Yes there is... the rf remote is connected directly to the box (not your print). Once the box is triggered via RF (either the original remote, or the "old" esp remote I already have) than the box doesn't respond to your pcb.
Tried several things:
- Made the box powerless for 30 seconds... reconnect the power, the module does not go active (I'll make a video of it)
- When changing speed via your module, the two leds on the mainboard won't lid
- When changing speed via RF, the left led (red) blinks 1x and the right led (amber) blinks several times
from ithowifi.
Ok, if you switch on the itho box and don't send any commands using RF or otherwise yet, does moving the slider on the webinterface change the speed of the itho?
from ithowifi.
Ok, if you switch on the itho box and don't send any commands using RF or otherwise yet, does moving the slider on the webinterface change the speed of the itho?
Yes, it works perfectly. MQTT connected and shows the speed changes too (either via the buttons, or slider).
Awkward ... while making a video, powerless for about 10 seconds, now it reconnects to the wifi when connected to the power again ... That's a minor ...
from ithowifi.
And if you used your remote and the last command given by remote is medium or auto (depending on your remote), what is then the result?
from ithowifi.
And if you used your remote and the last command given by remote is medium or auto (depending on your remote), what is then the result?
I've got a low/med/high/timer remote. When last command is medium, than the module can change the speed.
When pressing high or low on the remote, I can't use the module.
from ithowifi.
https://github.com/arjenhiemstra/ithowifi/raw/master/handleiding.pdf
Please read the second page: "belangrijk om te vermelden"
And since you have a HW rev 2 with CC1101 module, please also read page three to make use of the CC1101 module to circumvent this behaviour.
from ithowifi.
https://github.com/arjenhiemstra/ithowifi/raw/master/handleiding.pdf
Please read the second page: "belangrijk om te vermelden"
And since you have a HW rev 2 with CC1101 module, please also read page three to make use of the CC1101 module to circumvent this behaviour.
Check, read it ... that's a bummer
So best way is to connect the remote to the add-on? As mentioned in
Extra informatie hardware revisie 2 > RF remote support (alleen hardware revisie 2 – Experimenteel!):
from ithowifi.
Related Issues (20)
- Monitor only RF Devices not in remotesinfo HOT 5
- [Feature] Add OpenApi Spec / SwaggerUI to document api HOT 1
- Virtual remotes update remote broken HOT 2
- [Request] Ability to change through mqqt the default speed settings HOT 2
- Ventilation setpoint never goes below 30% HOT 2
- [Feature] Add fan/ventilation percentage to MQTT itho/ithostatus messages HOT 2
- Fan not keeping set speed HOT 14
- Request; turn off unit from HA HOT 2
- [Feature] autospeed relative to humidity
- HA: MQTT - TypeError: unsupported operand type(s) HOT 3
- [Request] Amber heat pump support HOT 6
- api.html?get=currentspeed not updating HOT 5
- [Request] AutoTemp fw 13 support HOT 7
- Minor typo in log message HOT 1
- Error on updating System Settings HOT 6
- Cannot switch off AP mode HOT 1
- long integer truncated in status JSON HOT 19
- [Feature Request] Support for WPU Version 41 HOT 32
- Virtual remote question HOT 2
- Rounding errors in statusvalues HOT 11
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ithowifi.