Build successfully but not recognized in webauth or U2F about opensk HOT 9 CLOSED

Did you already tried to push the reset button before the web server request authentication?

from opensk.

Did you already tried to push the reset button before the web server request authentication?

Yes I did press the reset...:(

from opensk.

@chillynoodles did the led1-4 blinking when the web asks for authentication?

from opensk.

@chillynoodles did the led1-4 blinking when the web asks for authentication?

Noop - I notice the led1-4 light off after flash OpenSK there. I did try again to run and flash again and shows:

Preparing to uninstall apps...
Only one app on board. Uninstalling ctap2
Uninstall complete.
No apps on board.
Finished in 1.976 seconds

Finished release [optimized] target(s) in 0.02s

Flashing binar(y|ies) to board...
Finished in 0.561 seconds

Installing apps on the board...
Finished in 3.654 seconds
and the board LED lights all go off - that's weird why I think it is flushed all....

Thank you for your help

from opensk.

@chillynoodles in my case, the led is off all the time, only blinks when the web ask for authentication.

Your log seems fine.

Have you tried this?
sudo cp rules.d/55-opensk.rules /etc/udev/rules.d/
sudo udevadm control --reload

from opensk.

@chillynoodles in my case, the led is off all the time, only blinks when the web ask for authentication.

Your log seems fine.

Have you tried this?
sudo cp rules.d/55-opensk.rules /etc/udev/rules.d/
sudo udevadm control --reload

Yes - i do. Can I ask you a question on your board behavior please?
When you press reset button of the board when connected with JLink, then unplug and use the web ask for auth with chrome, plug the board (USB peripherals) and it is passed?

I actually use https://demo.yubico.com/u2f/ and it prompts with "insert your security key", and I plug with board USB peripheral port and nothing happened...
Did you do the same steps?

Thanks,

from opensk.

Yes - i do. Can I ask you a question on your board behavior please?
When you press reset button of the board when connected with JLink, then unplug and use the web ask for auth with chrome, plug the board (USB peripherals) and it is passed?

I actually use https://demo.yubico.com/u2f/ and it prompts with "insert your security key", and I plug with board USB peripheral port and nothing happened...
Did you do the same steps?

Thanks,

Here is my steps,

• Flash the app using
  $ board=nrf52840dk ./deploy.sh app os
• Remove the JTag USB
• Connect the board into host PC via USB peripheral port (near reset button)
• Press reset (important)
• Open https://demo.yubico.com/u2f
• The web asks for authentication then my board's Led 1-4 blinking, just press any button from 1-4 and its authenticated.

By the way, i use Chrome.

from opensk.

Yes - i do. Can I ask you a question on your board behavior please?
When you press reset button of the board when connected with JLink, then unplug and use the web ask for auth with chrome, plug the board (USB peripherals) and it is passed?
I actually use https://demo.yubico.com/u2f/ and it prompts with "insert your security key", and I plug with board USB peripheral port and nothing happened...
Did you do the same steps?
Thanks,

Here is my steps,

• Flash the app using
  $ board=nrf52840dk ./deploy.sh app os
• Remove the JTag USB
• Connect the board into host PC via USB peripheral port (near reset button)
• Press reset (important)
• Open https://demo.yubico.com/u2f
• The web asks for authentication then my board's Led 1-4 blinking, just press any button from 1-4 and its authenticated.

By the way, i use Chrome.

I redo with what you did and press the reset button - it works!!!!
Really appreciate for your help!!! :)

from opensk.

Ooops - I can config and run fine with my nrf52840dk board and when I moved to nrf52840_dongle, run with existed same code by:

• Flash the app using $ board=nrf52840_dongle ./deploy.sh app os

• Remove the JTag USB, NRF52840 dongle and open https://demo.yubico.com/u2f

• The web asks for authentication and plug nrf52840 dongle and it does not recognize and nothing happend...
  Anyone can help to advice why it's working in nrf52840dk board but not with dongle please?

$ board=nrf52840_dongle ./deploy.sh app os
info: syncing channel updates for 'nightly-2020-02-03-x86_64-unknown-linux-gnu'

nightly-2020-02-03-x86_64-unknown-linux-gnu unchanged - rustc 1.42.0-nightly (f43c34a13 2020-02-02)

info: checking for self-updates
info: component 'rust-std' for target 'thumbv7em-none-eabi' is up to date
make: Entering directory '/home/chillybean/OpenSK/third_party/tock/boards/nordic/nrf52840_dongle'
Finished release [optimized + debuginfo] target(s) in 0.01s
text data bss dec hex filename
114176 1708 260436 376320 5be00 target/thumbv7em-none-eabi/release/nrf52840_dongle
tockloader flash --address 0x00000 --jlink --board nrf52dk target/thumbv7em-none-eabi/release/nrf52840_dongle.bin
Flashing binar(y|ies) to board...
Using known arch and jtag-device for known board nrf52dk
Finished in 7.898 seconds

make: Leaving directory '/home/chillybean/OpenSK/third_party/tock/boards/nordic/nrf52840_dongle'
Preparing to uninstall apps...
No apps are installed on the board

Finished release [optimized] target(s) in 0.02s

Flashing binar(y|ies) to board...
Finished in 7.862 seconds

Installing apps on the board...
Finished in 22.409 seconds

from opensk.