Comments (1)
DivingDuck
commented on August 27, 2024
1
Hi @equalsai,
Thanks for your report. Please add as well the version of Pronterface and your operating system to your report.
Maybe I oversee something, but can you tell me what command is not executed?
I copied your code and executed it on my system (firmware smoothieware) as there is nothing special on your gcode.
Show test gcode
G0 Z10 S0
G90
G21
G1 F1000
G1 X122.4164 Y129.3071
G4 P0
G0 Z0 S0
G4 P0
G1 F1000.000000
G1 X173.5241 Y129.3071
G1 X173.5241 Y64.5357
G1 X169.0267 Y64.5357
G1 X169.0267 Y68.0069
G1 X126.9139 Y68.0069
G1 X126.9139 Y64.4663
G1 X122.4164 Y64.4663
G1 X122.4164 Y129.3071
G4 P0
G0 Z10 S0
G1 F1000
G1 X108.5735 Y112.7845
G4 P0
G0 Z0 S0
G4 P0
G1 F1000.000000
G1 X90.642 Y112.7845
G1 X90.642 Y95.1511
G1 X108.5735 Y95.1511
G1 X108.5735 Y112.7845
This is the communication log:
Show log
2024-08-22 09:21:35,977 - Druck gestartet bei: 09:21:35
2024-08-22 09:21:35,979 - SENT: N0 G0 Z10 S0*17
2024-08-22 09:21:35,982 - RECV: ok T:22.6 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:20.9 /0.0 @0
2024-08-22 09:21:35,983 - RECV: ok
2024-08-22 09:21:35,992 - SENT: N1 G90*17
2024-08-22 09:21:35,993 - RECV: ok
2024-08-22 09:21:36,008 - SENT: N2 G21*24
2024-08-22 09:21:36,009 - RECV: ok
2024-08-22 09:21:36,024 - SENT: N3 G1 F1000*76
2024-08-22 09:21:36,025 - RECV: ok
2024-08-22 09:21:36,026 - SENT: N4 G1 X122.4164 Y129.3071*36
2024-08-22 09:21:36,040 - RECV: ok
2024-08-22 09:21:36,056 - SENT: N5 G4 P0*104
2024-08-22 09:21:44,914 - RECV: ok
2024-08-22 09:21:44,915 - SENT: M117 20.69% Est 0.00.24
2024-08-22 09:21:44,916 - RECV: ok
2024-08-22 09:21:44,930 - SENT: M105
2024-08-22 09:21:44,936 - RECV: ok T:22.6 /0.0 @0 T1:22.1 /0.0 @0 B:21.5 /0.0 @0 B1:21.0 /0.0 @0
2024-08-22 09:21:44,946 - SENT: N6 G0 Z0 S0*38
2024-08-22 09:21:45,512 - RECV: ok
2024-08-22 09:21:45,521 - SENT: M105
2024-08-22 09:21:45,527 - RECV: ok T:22.7 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:21.0 /0.0 @0
2024-08-22 09:21:45,536 - SENT: N7 G4 P0*106
2024-08-22 09:21:45,537 - RECV: ok
2024-08-22 09:21:45,552 - SENT: N8 G1 F1000.000000*105
2024-08-22 09:21:45,554 - RECV: ok
2024-08-22 09:21:45,568 - SENT: N9 G1 X173.5241 Y129.3071*40
2024-08-22 09:21:45,571 - RECV: ok
2024-08-22 09:21:45,584 - SENT: N10 G1 X173.5241 Y64.5357*41
2024-08-22 09:21:50,028 - RECV: ok
2024-08-22 09:21:50,039 - SENT: M105
2024-08-22 09:21:53,910 - RECV: ok T:22.7 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:21.0 /0.0 @0
2024-08-22 09:21:53,923 - SENT: M117 37.93% Est 0.00.19
2024-08-22 09:21:53,924 - RECV: ok
2024-08-22 09:21:53,939 - SENT: N11 G1 X169.0267 Y64.5357*34
2024-08-22 09:21:53,941 - RECV: ok
2024-08-22 09:21:53,955 - SENT: N12 G1 X169.0267 Y68.0069*38
2024-08-22 09:21:54,206 - RECV: ok
2024-08-22 09:21:54,218 - SENT: N13 G1 X126.9139 Y68.0069*45
2024-08-22 09:21:54,446 - RECV: ok
2024-08-22 09:21:54,452 - SENT: N14 G1 X126.9139 Y64.4663*46
2024-08-22 09:21:56,959 - RECV: ok
2024-08-22 09:21:56,961 - SENT: M105
2024-08-22 09:21:57,198 - RECV: ok T:22.7 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:21.0 /0.0 @0
2024-08-22 09:21:57,211 - SENT: N15 G1 X122.4164 Y64.4663*46
2024-08-22 09:21:57,214 - RECV: ok
2024-08-22 09:21:57,226 - SENT: N16 G1 X122.4164 Y129.3071*23
2024-08-22 09:21:57,490 - RECV: ok
2024-08-22 09:21:57,491 - SENT: N17 G4 P0*91
2024-08-22 09:22:01,320 - RECV: ok
2024-08-22 09:22:01,330 - SENT: M105
2024-08-22 09:22:01,335 - RECV: ok T:22.7 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:21.1 /0.0 @0
2024-08-22 09:22:01,345 - SENT: N18 G0 Z10 S0*40
2024-08-22 09:22:01,920 - RECV: ok
2024-08-22 09:22:01,922 - SENT: N19 G1 F1000*119
2024-08-22 09:22:01,924 - RECV: ok
2024-08-22 09:22:01,937 - SENT: N20 G1 X108.5735 Y112.7845*26
2024-08-22 09:22:01,940 - RECV: ok
2024-08-22 09:22:01,952 - SENT: N21 G4 P0*94
2024-08-22 09:22:03,385 - RECV: ok
2024-08-22 09:22:03,386 - SENT: N22 G0 Z0 S0*16
2024-08-22 09:22:05,253 - RECV: ok
2024-08-22 09:22:05,256 - SENT: M117 79.31% Est 0.00.05
2024-08-22 09:22:05,257 - RECV: ok
2024-08-22 09:22:05,272 - SENT: M105
2024-08-22 09:22:05,278 - RECV: ok T:22.7 /0.0 @0 T1:22.0 /0.0 @0 B:21.6 /0.0 @0 B1:21.1 /0.0 @0
2024-08-22 09:22:05,287 - SENT: N23 G4 P0*92
2024-08-22 09:22:05,289 - RECV: ok
2024-08-22 09:22:05,302 - SENT: N24 G1 F1000.000000*87
2024-08-22 09:22:05,303 - RECV: ok
2024-08-22 09:22:05,303 - SENT: N25 G1 X90.642 Y112.7845*27
2024-08-22 09:22:05,307 - RECV: ok
2024-08-22 09:22:05,318 - SENT: N26 G1 X90.642 Y95.1511*44
2024-08-22 09:22:06,317 - RECV: ok
2024-08-22 09:22:06,332 - SENT: N27 G1 X108.5735 Y95.1511*41
2024-08-22 09:22:08,805 - RECV: ok
2024-08-22 09:22:08,808 - SENT: M105
2024-08-22 09:22:09,885 - RECV: ok T:22.7 /0.0 @0 T1:22.1 /0.0 @0 B:21.5 /0.0 @0 B1:21.0 /0.0 @0
2024-08-22 09:22:09,901 - SENT: N28 G1 X108.5735 Y112.7845*18
2024-08-22 09:22:09,904 - RECV: ok
2024-08-22 09:22:09,916 - SENT: M110 N-1
2024-08-22 09:22:09,917 - Druck beendet um: 09:22:09 und dauerte 0:00:33
2024-08-22 09:22:10,207 - SENT: M117 Finished Print
2024-08-22 09:22:10,369 - SENT: M105
2024-08-22 09:22:10,950 - RECV: ok
2024-08-22 09:22:10,951 - RECV: ok
I can't see any error or unusual behavior in Pronterface.
Looking at your log I wonder from what the output below N27 is. In N27 you make a simple G1 movement. There should be no communication from your machine back to Pronterface except a received message <RECV: ok>.
Btw, you can log the communication directly within Pronterface. -->Settings -->Debug Communications. There is also a log file available at your home directory. The file is called printrun.log. Under -->Settings -->Options -->User Interface you can find the location as well.
Test file, log and screenshot: TestFilePic&Log.zip
from printrun.
Related Issues (20)
- AttributeError: 'NoneType' object has no attribute 'write HOT 3
- Do not disable extruder on exit HOT 8
- Multiple printer config files HOT 9
- faild to execute script pronterface HOT 4
- what's the game? HOT 12
- Appdirs is now dead upstream
- Problems if try to print a file, just after print the previous one HOT 6
- my pronterface doesnt want to open im about to go insane HOT 3
- CI actions not working as expected HOT 22
- Translation files for macOS HOT 3
- 2.1.0 crash during print on macos 14.4 HOT 14
- Error of 2D viewer when loading gcode files with G2/G3 arcs HOT 3
- Bacup to earlier layer after fail HOT 3
- App crashes when open on multiple users (macos) HOT 3
- liam HOT 1
- pronterface
- problem when changing speed slider HOT 8
- constant ok messages HOT 3
- errors when doing `python3 setup.py build_ext --inplace` HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from printrun.