Comments (10)
from aqualinkd.
I had a PI setup in my control panel outside, (before I got my SWG working with the Control Panel I had a version or AqualinkD controlling the SWG). I had a lot of instability due to the heat in the summer. I do live in a very hot climate, and the panel got direct sunlight for the majority of the day though.
from aqualinkd.
Thank you I'm going to try this. Well first powering it from the OneTouch so I don't have a power cord hanging down the wall. I'll think about moving it to the panel later, I'm wondering if the heat will be an issue for me as well (Dallas).
from aqualinkd.
I too had my setup in the Control Panel, but heat and bad Wi-fi made me move it into my Aqualink RS6 Panel and it works great!
Simple adaptation - Raspberry Pi Zero W, 12V to 5V converter, RS485 to USB Converter. Data and Power from Panel 4 Pin connector using extra USB Cables...
from aqualinkd.
This is great. I always wondered if I could make it all fit in the RS6 keypad. Know I know.
from aqualinkd.
If people have interest in this I could design a dedicated board that can sit right next to the original that the Pi can just snap into. No more dongles or electrical tape.
from aqualinkd.
I am interested in this. I already have a buck converter and a 12 to 5v step down. I do not have an interior panel so I am looking to install in the control panel. If I understand, the low voltage rs485 power is 12v and I can tap into that, correct?
from aqualinkd.
Be careful, not all are 12v. (Most are though). So make sure to use a meter if your DC/DC converter expects 12v rather than a range. If installing in panel, you already have 110v, so you can simply add a USB adapter if needed. There is nothing wrong with this approach, and I'm currently doing something very similar. BUT Pi's can be really finicky on power, and if you have a power issue, the first thing that will start acting up is USB and CPU speed. That will have detrimental effects on AqualinkD as RS485 and timing is key. So if you go down this path, just make sure to spec everything appropriately.
from aqualinkd.
Thank you. I used a voltmeter and it was DC voltage around 15V. I was able to step it down to 5V/3A by connecting 1(+)/4(-). I then connected 2(+)/3(-) to my adapter. So far so good.
from aqualinkd.
I left the pi's outside of the box, and have one of these tucked in the aqualink panel for power.
I have aspirations of more advanced pool functions so added in a a 120vac -> 20vdc convertor, and then bolted up the dc dc step down.
"Aiposen 110V/220V AC to DC 24V 2A 48W Switch Power Supply Driver,Power Transformer for CCTV Camera/Security System/LED Strip Light/Radio/Computer Project(24V 2A)"
https://www.amazon.com/gp/product/B01B1PRE42/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
and
"BINZET DC Converter Step Down Regulator 5V Regulated Power Supplies Transformer Converter (5V 3A 15W)"
https://www.amazon.com/gp/product/B00J3MHRNO/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1
from aqualinkd.
Related Issues (20)
- Pool Light Dimmer Web UI Confusing HOT 3
- Support Light Dimmer in Homebridge Plugin
- SWG percentage setting not working for PDA
- With raspberry pi 4 aqualinkd is responding too fast and panel may reset
- VSP control for Aqualinkd HOT 3
- Misconfigured Buttons. RS-8 Combo Panel HOT 4
- Getting wrong Temperature via MQTT but ok in web interface HOT 2
- Serial Packet Too Large - Read Bad Packet to 0x33 HOT 4
- AqualinkD Devices in MQTT for HASS?
- V2.3.4 make fails on bullseye - multiple definition of `_commands' HOT 6
- Support sharing same PDA ID between control panel and physical PDA HOT 1
- "Notes on Aqualink PDA only (non RS panels)" link goes nowhere HOT 3
- Aqualink daemon can't use extended_device_id in PDA mode HOT 3
- Got working with EW-11 wireless device! HOT 23
- VSP Variable speed pump control without Aqualink support? HOT 1
- iaqtouch_aq_programmer.c:942:11: error: invalid type argument of unary '*' HOT 5
- Would this adapter work? HOT 1
- iAQ Touch: IAQ Touch did not find Set Temp page
- iAQ Touch: Pool Temp set incorrect
- Pool / Spa temperature incorrect HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from aqualinkd.