Comments (8)
@BobClav I just posted an update that should display VSP info from the PDA menu. Still working on decoding protocol so I can read vPump into directly.
from aqualinkd.
Thanks very much, I hope that shouldn't be necessary. Give me a few days to see if I can decode the information you have already logged for me.
from aqualinkd.
In the debug logs you sent, it never for to the "equipment status" menu which is where the RPM is shown, it only get's to the "equipment" menu. Leave it running for longer, and please post the logs.
At the moment, AqualinkD can only read the pump RPM / GPM directly from Pentair pumps, and you have a Jandy pump, so AqualinkD has to wait for the message to be shown in the equipment status.
Even if this works, please do post a longer set of logs, and even better if you can post with changing the RPM (on the PDA or AqualinkD). That way I can figure out the Jandy ePump protocol and make AqualinkD faster at reading those RPM values.
As for GPM, AqualinkD will only display the value that can be changed, with a ePump, I believe that's RPM and not GPM.
from aqualinkd.
Thanks for the quick response. Attached is another debug log that shows the ePump values that would appear on the screen. Also note that it displays power usage (Watts). It would be awesome to have the icon toggle back and forth the RPMs and then WATTS.
Back to the issue, the pump motor icon shows RPM as 520, which is in the logfile, just the wrong value selected. Is it possibly the naming I am using for the ePump?
from aqualinkd.
Thank. I see the problem, it'll take a bit to fix though. In the mean time, if you get chance, can you post exactly the same log, but with a different RPM/GPM on the VSP?
Also do you know the version# of your panel?
from aqualinkd.
PDA: 7.1.0
J-Box: 4.0
Handheld: 3.0
I ran through 3 different speeds SPEED4: @3450, SWEEP: @2900 and back to POOL: @2520 . Note that looking at the debug log, the RPMs do not show when the PDA is active, but WATTS do. I shut off the PDA and the RPMs show up then.
Let me know if you need to to try anything else.
from aqualinkd.
Thanks so much, very helpful. I'm more interested in the below type messages when you have set the speed on the PDA, vs what the PDA states it's set to. And I can see all that in the log. The HEX is what the control panel is sending the pump, and what the pump is returning. This allows me to try to decode the ePump protocol.
Debug: JandyDvce: To ePump: Read To 0x78 of type Unknown '0x44' | HEX:0x10|0x02|0x78|0x44|0x00|0x60|0x27|0x55|0x10|0x03|
Debug: JandyDvce: From ePump: Read To 0x00 of type Unknown '0x1f' | HEX:0x10|0x02|0x00|0x1f|0x44|0x00|0x60|0x27|0x00|0xfc|0x10|0x03|
Debug: JandyDvce: To ePump: Read To 0x78 of type Unknown '0x41' | HEX:0x10|0x02|0x78|0x41|0xcb|0x10|0x03|
Debug: JandyDvce: From ePump: Read To 0x00 of type Ack | HEX:0x10|0x02|0x00|0x01|0x41|0x00|0x54|0x10|0x03|
from aqualinkd.
If you need/want access, let me know. Think you have direct contact info in github.
from aqualinkd.
Related Issues (20)
- systemctl start fails. Command line works. HOT 7
- Pool Light Dimmer Web UI Confusing HOT 3
- Support Light Dimmer in Homebridge Plugin
- SWG percentage setting not working for PDA
- With raspberry pi 4 aqualinkd is responding too fast and panel may reset
- VSP control for Aqualinkd HOT 3
- Misconfigured Buttons. RS-8 Combo Panel HOT 4
- Getting wrong Temperature via MQTT but ok in web interface HOT 2
- Serial Packet Too Large - Read Bad Packet to 0x33 HOT 4
- AqualinkD Devices in MQTT for HASS?
- V2.3.4 make fails on bullseye - multiple definition of `_commands' HOT 6
- Support sharing same PDA ID between control panel and physical PDA HOT 1
- "Notes on Aqualink PDA only (non RS panels)" link goes nowhere HOT 3
- Aqualink daemon can't use extended_device_id in PDA mode HOT 3
- Got working with EW-11 wireless device! HOT 7
- VSP Variable speed pump control without Aqualink support? HOT 1
- iaqtouch_aq_programmer.c:942:11: error: invalid type argument of unary '*' HOT 5
- Would this adapter work? HOT 1
- iAQ Touch: IAQ Touch did not find Set Temp page
- iAQ Touch: Pool Temp set incorrect
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from aqualinkd.