Comments (13)
If the RS keypad heater lights up, then that's the correct functionality. AqualinkD uses the RS naming, so I think what you might be looking for is "solar heater" on the RS Keypad. To confirm, turn on the heater on the OneTouch, and look at what's lit on the RS keypad. If it's the solar heater, then just uncomment solar heater in the web configuration file.
On a default installation that's the file in
/var/www/aqualinkd/config.js
In the web UI section of the wiki (although not well described)
https://github.com/sfeakes/AqualinkD/wiki#AqualinkDweb
from aqualinkd.
When I turn it on via the iaqualink the heater light comes on and solar heater stays off
from aqualinkd.
from aqualinkd.
Thats what it shows in iaqualink when I turn on the spa mode
from aqualinkd.
this is what AqualinkD shows while the heater is running
from aqualinkd.
Im a little confused. In your original post you said jandy rs it lights up the light. Do you mean the Jandy RS Keypad lights up the light / RS Control panel lights up the light, and I'm assuming the heater light.
Either way, edit the web config, uncomment the solar heater line. (clear web browser cache & reload aqualinkd). This should now show you every button available to AqualinkD. Turn everything off in iAqualink, Make sure AqualinkD shows everything as off. Then turn on the heater on iAqualink. See what (if anything) turns on in AqualinkD. That should tell you what button it's configured to.
There are 5 fixed buttons on the Jandy equipment (Pool pump / Spa mode / Pool Heater / Spa Heater & Solar Heater) all others are configurable. Most installers follow this fixed assignment, but you can easily change them around, it just means the labels will read incorrectly on the all button keypads.
In saying that, the last 3 (heaters) are assigned differently if your control panel can support 12 or 14 devices, control panels that support up to 10 devices use the same assignment that AqualinkD defaults to. This might be the problem, but I haven't come across it yet.
from aqualinkd.
Oh. One other thing I see looking at the images, and not knowing your exact pool equipment setup. Is maybe the heat pump is configured to only come on while heating and not when "up to temp", in which case the Orange background vs Green background on the temperature icon within Spa heat / Pool Heat gives you that indication.
Example, I have a gas heater and no heat pump. Green background means the heater is ENABLED but not actually heating. Orange means ENABLED & HEATING. Ie orange means on and heating, green means on but not heating as water it up to temperature.
Without knowing your pool equipment setup and how it's all configured it's extremely hard to tell if it's acting correctly. If you have an all button keypad then AqualinkD should mimic the LED's on that exactly.
from aqualinkd.
from aqualinkd.
Hello @sfeakes ,
Im just getting back to working on this. Here is what I am seeing in Jandys website for what turns on when I turn on the spa. Aqualinkd is not showing the heat pump as a option. Please advise what I have to adjust to see that icon.
from aqualinkd.
I'm having a similar issue I think. I got everything working as far as I can tell, but the button config is confusing since the first button on my panel box controller seems to be a service mode selector, but AqulinkD uses button #1 as Filter pump. In any case, when I turn on spa mode at my wired Jandy remote panel, the spa heater comes on. When I turn on spa mode in AqualinkD, it says spa mode is on but no heater.
from aqualinkd.
If I understand your problem correctly. When you hit "spa mode" on jandy keypad, it sets pump(s) / JVA's to Spa setting AND also turns on spa heater. But when you hit "spa" button in AqualinkD it sets pump(s) / JVA's to Spa setting but does not turn on spa heater?
If so, then that's correct. Spa mode is actually different between different Jandy control panels. OneTouch & IAqualinkTouch both have both Spa and Spa Mode options, but Allbutton keypad only has Spa. You should just be able to hit the spa heater button on AqualinkD to turn on the spa heater.
I do agree AqualinkD saying "Spa Mode" when it's actually "Spa" is confusing. When I wrote this I was going by equipment and Jandy documentation I had available. Jandy change this with the introduction of other keypads, and it's only recently (last few months) I realized that "Spa" and "Spa Mode" are actually different things with Jandy.
So : -
"Spa" is Pumps & JVA's
"Spa Mode" is Pumps, JVA's & heater.
AqualinkD is Spa even though the button says Spa Mode.
If you are using a home automation hub, you can configure a "Spa Mode" button that selects both AqualinkD's Spa Mode and Spa Heater buttons.
from aqualinkd.
Thanks very much for the quick reply and detailed explanation! I should have mentioned that I really appreciate the work you put into this project! Very nice job!
from aqualinkd.
Just posted V2.1.1. That has a config option to link Spa Mode and Spa Heater. Please see documentation / release notes. I've restricted it to just webUI as to not confuse home automation implementations.
from aqualinkd.
Related Issues (20)
- systemctl start fails. Command line works. HOT 7
- Pool Light Dimmer Web UI Confusing HOT 3
- Support Light Dimmer in Homebridge Plugin
- SWG percentage setting not working for PDA
- With raspberry pi 4 aqualinkd is responding too fast and panel may reset
- VSP control for Aqualinkd HOT 3
- Misconfigured Buttons. RS-8 Combo Panel HOT 4
- Getting wrong Temperature via MQTT but ok in web interface HOT 2
- Serial Packet Too Large - Read Bad Packet to 0x33 HOT 4
- AqualinkD Devices in MQTT for HASS?
- V2.3.4 make fails on bullseye - multiple definition of `_commands' HOT 6
- Support sharing same PDA ID between control panel and physical PDA HOT 1
- "Notes on Aqualink PDA only (non RS panels)" link goes nowhere HOT 3
- Aqualink daemon can't use extended_device_id in PDA mode HOT 3
- Got working with EW-11 wireless device! HOT 23
- VSP Variable speed pump control without Aqualink support? HOT 1
- iaqtouch_aq_programmer.c:942:11: error: invalid type argument of unary '*' HOT 5
- Would this adapter work? HOT 1
- iAQ Touch: IAQ Touch did not find Set Temp page
- iAQ Touch: Pool Temp set incorrect
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from aqualinkd.