Comments (10)
from aqualinkd.
MQTT holds the last value, so that would be it. Turn the hot tub on without the heater and that’ll sort it out..:). I’ll work on a solution, but a - wouldn’t work, I’ll probably have to use the pool water temp if the hot tub is not on.
from aqualinkd.
@johnluber I just committed an update to do this. Looked at a few options, best seemed to be simply post the pool water temp to spa water temp when in pool mode. Can't use '-' as iOS doesn't;t support it, using 0 would mean changing the Thermostat range to work from 0 to 110, but Aqualink only supports 40 and above, so would cause other issues.
On a side note, I'm trying to control the SWG AquaPure & AquaRite in a better manor, would you mind running a piece of diagnostics software on your system for 10 or 15 mins and posting the output?
If so, can you stop aqualinkd, turn off SWG, run diagnostics, press a few buttons, and post output?
Commands are
sudo systemctl stop aqualinkd
(turn off SWG - turns on/off with pump usually)
sudo /.../aqualinkd/release/aquarite_logger /dev/ttyUSB0 > aqua.out
(turn on SWG )
wait for SWG to show "remote controlled" / or "no flow" is not flashing
use control panel to set SWG % to 25
wait a few seconds
use control panel to set SWG % to 50
wait a few seconds
kill diagnostics
CTRL-C
sudo systemctl start aqualinkd
Post the file aqua.out
Cheers
from aqualinkd.
from aqualinkd.
Hi Shaun
Sorry for not getting back sooner. Been doing some business travel and then had a network outage that got in the way of things here.
I did install the new binary and had a chance to do some usage testing last night. Unfortunately, the aqualinkd crashed when trying to turn on the pool lights. Previously, I hadn't been having a problem with this.
I've reverted to the previous version and am attaching the log from the crash.
Thanks!
john
aqualinkd.log
from aqualinkd.
Hi, first time post to the site, wanted to start by saying thanks for putting this stuff out there, great work. I'm actually new to the pool world but come from an Automation background, i have the PI zero config setup but unfortunantly have the PDA that came with the pool, let me know if you need any testers for the PDA version, i have a background in manufacturing systems so i'm quite use to some of these debug environments.
from aqualinkd.
I have this support in the latest version. It now reports 0 or 32 depending on degC or degF on your phone. I tried 0 degF and it was unstable, I will play some more. You should also update the Thermostat configuration for homekit2mqtt (see example in extras directory). Also supports SWG now, so you can set % generating rather than just viewing it. (again see homekit2mqtt.json example in extras directory)
from aqualinkd.
I'm still available to test the PDA version if you need anyone.
from aqualinkd.
I have played with this slowly, but it’s a kinda pain. Still need to spend a lot more work on it. Someone recently told me that you can change a chip on the control panel circuit board, and convert the PDA only to RS and PDA functionality. Said they were around $100 off eBay. He used that to get option to get AqualinkD working in his setup.
from aqualinkd.
Closing this as original issue is fixed. Opened a new issue for PDA support.
from aqualinkd.
Related Issues (20)
- Pool Light Dimmer Web UI Confusing HOT 3
- Support Light Dimmer in Homebridge Plugin
- SWG percentage setting not working for PDA
- With raspberry pi 4 aqualinkd is responding too fast and panel may reset
- VSP control for Aqualinkd HOT 3
- Misconfigured Buttons. RS-8 Combo Panel HOT 4
- Getting wrong Temperature via MQTT but ok in web interface HOT 2
- Serial Packet Too Large - Read Bad Packet to 0x33 HOT 4
- AqualinkD Devices in MQTT for HASS?
- V2.3.4 make fails on bullseye - multiple definition of `_commands' HOT 6
- Support sharing same PDA ID between control panel and physical PDA HOT 1
- "Notes on Aqualink PDA only (non RS panels)" link goes nowhere HOT 3
- Aqualink daemon can't use extended_device_id in PDA mode HOT 3
- Got working with EW-11 wireless device! HOT 23
- VSP Variable speed pump control without Aqualink support? HOT 1
- iaqtouch_aq_programmer.c:942:11: error: invalid type argument of unary '*' HOT 5
- Would this adapter work? HOT 1
- iAQ Touch: IAQ Touch did not find Set Temp page
- iAQ Touch: Pool Temp set incorrect
- Pool / Spa temperature incorrect HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from aqualinkd.