TinyGo for Arduino

🧭 Introduction

📖 Slide deck

📖 Documentation

📖 TinyGo machine package for Arduino Uno.
📖 Arduino Projects Book, license CC-BY-NC-SA by Arduino LLC.

🧰 Do It Yourself (DIY)

💻 Hello world! (PC/Go version)

package main

func main() {
    println("Hello! 👋")
}

Run from source:

$ go run app.go
Hello! 👋

Compile:

$ go build app.go
$ ls
app  app.go

Execute:

$ ./app 
Hello! 👋

File size:

$ du -h app
1,2M	app

Cross-compile (Windows):

$ GOOS=windows go build app.go 
 ls
app  app.exe  app.go
$ du -h app.exe 
1,2M	app.exe

Cross-compile (Apple Silicon):

$ rm app app.exe
$ ls
app.go
$ GOOS=darwin GOARCH=arm64 go build app.go
$ ls
app  app.go
$ du -h app
1,1M	app

ℹ️ If you use Visual Studio Code, you may install the Go extension to get code completion, signature help, etc.

💻 Hello world! (PC/TinyGo version)

package main

func main() {
    println("Hello! 👋")
}

Run from source:

$ tinygo run app.go
Hello! 👋

Build:

$ tinygo build app.go
(base) boisgera@oddball:~/tmp/sandbox$ ls
app  app.go
(base) boisgera@oddball:~/tmp/sandbox$ du -h app
68K	app

Execute:

$ ./app 
Hello! 👋

📟 Hello world! (Arduino/TinyGo version)

package main

func main() {
    println("Hello from Arduino! 👋")
}

tinygo flash -target=arduino app.go

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "/tmp/tinygo287452646/main.hex"
avrdude: writing flash (1174 bytes):

Writing | ################################################## | 100% 0.20s

avrdude: 1174 bytes of flash written
avrdude: verifying flash memory against /tmp/tinygo287452646/main.hex:
avrdude: load data flash data from input file /tmp/tinygo287452646/main.hex:
avrdude: input file /tmp/tinygo287452646/main.hex contains 1174 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.16s

avrdude: verifying ...
avrdude: 1174 bytes of flash verified

avrdude done.  Thank you.

If you are familiar with Python, you can read this message with:

pip install pyserial

import serial

# ⚙️ Configuration
BAUD_RATE = 9600
SERIAL_PORT = "/dev/ttyACM0"

# ⏳ Loop
with serial.Serial(SERIAL_PORT, BAUD_RATE) as file:
    while True:
        bytes = file.readline().strip()
        print(bytes.decode("utf-8"))

$ python read.py
Hello from Arduino! 👋
⏳

But there is a simpler alternative with TinyGo:

$ tinygo flash -monitor -baudrate=9600 -target arduino app.go
...
Connected to /dev/ttyACM0. Press Ctrl-C to exit.
Hello from Arduino! 👋
⏳

⏱️ Time

package main

import "time"

func main() {
    for i := 0; i < 3; i++ {
        println("Hello from Arduino! 👋")
        time.Sleep(500 * time.Millisecond)
    }
}

$ tinygo flash -monitor -baudrate=9600 -target arduino app.go
...
Connected to /dev/ttyACM0. Press Ctrl-C to exit.
Hello from Arduino! 👋
Hello from Arduino! 👋
Hello from Arduino! 👋
⏳

package main

import "time"

func main() {
    for {
        println("Hello from Arduino! 👋")
        time.Sleep(500 * time.Millisecond)
    }
}

$ tinygo flash -monitor -baudrate=9600 -target arduino app.go
...
Connected to /dev/ttyACM0. Press Ctrl-C to exit.
Hello from Arduino! 👋
Hello from Arduino! 👋
Hello from Arduino! 👋
⏳

⚠️ The standard Timer & Ticker standard API would be super nice to have, but they are buggy at the moment.

🚥 Blinky

package main

import (
    "machine"
    "time"
)

var Output = machine.PinConfig{Mode: machine.PinOutput}

func main() {
    led := machine.LED // i.e. machine.D13 (a Pin)
    led.Configure(Output)
    for {
        led.Low()
        time.Sleep(1000 * time.Millisecond)
        led.High()
        time.Sleep(3000 * time.Millisecond)
    }
}

tinygo flash -target=arduino app.go

ℹ️ If you use Visual Studio Code, you may install the TinyGo extension and select the arduino target to get code completion and signature help for the machine package. For more details, refer to the TinyGo documentation.

📄 Intel HEX

Intel hexadecimal object file format, Intel hex format or Intellec Hex is a file format that conveys binary information in ASCII text form. It is commonly used for programming microcontrollers, EPROMs, and other types of programmable logic devices and hardware emulators. In a typical application, a compiler or assembler converts a program's source code (such as in C or assembly language) to machine code and outputs it into a HEX file. [...] The HEX file is then read by a programmer to write the machine code into a PROM or is transferred to the target system for loading and execution.

(Wikipedia)

tinygo build -o app.hex -target=arduino app.go

$ cat app.hex
:100000000C9434000C9472020C9472020C947202E0
:100010000C9472020C9472020C9464020C9472029E
:100020000C9472020C9472020C9472020C94720280
...
:10007000BEBF0F92A0E0B3E0C4E6D3E0EEE1F5E04E
:1005700066726F6D2041726475696E6F2120F09F05
:02058000918B5D
:00000001FF

pip install intelhex

$ hexinfo.py app.hex
- file: 'app.hex'
  data:
  - { first: 0x00000000, last: 0x00000581, length: 0x00000582 }

>>> 0x00000582 
1410

(1410 bytes, well below the 32 kb limit for Arduino Uno).

Then instead of tinygo flash, do:

avrdude -C /etc/avrdude.conf -p atmega328p -c arduino -P /dev/ttyACM0 -D -U flash:w:app.hex:i

$ man avrdude
AVRDUDE(1)                BSD General Commands Manual               AVRDUDE(1)

NAME
     avrdude — driver program for ``simple'' Atmel AVR MCU programmer

SYNOPSIS
     avrdude -p partno [-b baudrate] [-B bitclock] [-c programmer-id]
             [-C config-file] [-D] [-e] [-E exitspec[,exitspec]] [-F]
             [-i delay] [-n -logfile] [-n] [-O] [-P port] [-q] [-s] [-t] [-u]
             [-U memtype:op:filename:filefmt] [-v] [-x extended_param] [-V]
...

💻 WokWi Simulator

Sign into https://wokwi.com/.
Start from Scratch with Arduino Uno. You may rename the project "Blinky" instead of "sketch.ino" and delete the sketch.ino file ; we won't need it.
In the editor, right-click and open the command palette (or press F1).
Select "Load HEX File and Start Simulation ..." and upload your app.hex file.
Profit! 🎉

🚥 LED

To replicate the Blinky project, but with an external LED instead of the onboard one, we need little change in the app.go program; if we intend to connect the LED D4, we have:

package main

import (
    "machine"
    "time"
)

var Output = machine.PinConfig{Mode: machine.PinOutput}

func main() {
    led := machine.D4
    led.Configure(Output)
    for {
        led.Low()
        time.Sleep(1000 * time.Millisecond)
        led.High()
        time.Sleep(3000 * time.Millisecond)
    }
}

🔲 Toggle Button + LED

To switch the LED state, press the button during at least 0.1 seconds, then release it.

package main

import (
    "machine"
    "time"
)

var Input = machine.PinConfig{Mode: machine.PinInput}
var Output = machine.PinConfig{Mode: machine.PinOutput}

var ButtonPin = machine.D2
var ButtonWasPressed = false

var LightPin = machine.D4
var LightOn = false

func setup() {
    LightPin.Configure(Output)
    ButtonPin.Configure(Input)
}

func ButtonHandler() {
    ButtonPressed := !ButtonPin.Get()
    ButtonRelease := !ButtonPressed && ButtonWasPressed
    if ButtonRelease {
        LightOn = !LightOn
    }
    ButtonWasPressed = ButtonPressed
}

func LightHandler() {
    if LightOn {
        LightPin.High()
    } else {
        LightPin.Low()
    }
}

func main() {
    setup()
    for {
        ButtonHandler()
        LightHandler()
        time.Sleep(100 * time.Millisecond)
    }
}

📉 ADC

package main

import (
    "machine"
    "time"
)

var adc = machine.ADC{Pin: machine.ADC0}

func setup() {
    machine.InitADC()
}

func main() {
    setup()
    for {
        println(adc.Get() >> 6)
        time.Sleep(1 * time.Second)
    }
}

diagram.json:

{
  "version": 1,
  "author": "Sébastien Boisgérault",
  "editor": "wokwi",
  "parts": [
    { "type": "wokwi-arduino-uno", "id": "uno", "top": 0, "left": 0, "attrs": {} },
    {
      "type": "wokwi-slide-potentiometer",
      "id": "pot1",
      "top": 223.8,
      "left": 38.76,
      "attrs": { "travelLength": "30" }
    }
  ],
  "connections": [
    [ "uno:GND.2", "pot1:GND", "black", [ "v36.18", "h-178.04" ] ],
    [ "uno:5V", "pot1:VCC", "red", [ "v38.57", "h-120.71" ] ],
    [ "uno:A0", "pot1:SIG", "green", [ "v21.83", "h56.09", "v118.38", "h-229.59" ] ]
  ]
}

📈 PWM

See Using PWM.

⚠️ Floating-point computations are not used here. They are not supported by the hardware and thus have to be emulated in software and this is costly.

package main

import (
    "machine"
    "time"
)

var pwm machine.PWM
var pwmPin = machine.D5
var period uint64
var ch uint8

func setup() {
    pwm.Configure(machine.PWMConfig{})
    period = pwm.Period() // 16_000 ns
    var err error
    ch, err = pwm.Channel(pwmPin)
    if err != nil {
        panic(err)
    }
}

func main() {
    setup()
    top := pwm.Top()
    x := top
    for {
        println(x)
        pwm.Set(ch, x)
        x = x - top/100
        if x == 0 {
            x = top
        }
        time.Sleep(10 * time.Duration(period))
    }
}

diagram.json:

{
  "version": 1,
  "author": "Sébastien Boisgérault",
  "editor": "wokwi",
  "parts": [
    { "type": "wokwi-arduino-uno", "id": "uno", "top": 159.41, "left": 11.03, "attrs": {} },
    {
      "type": "wokwi-led",
      "id": "led1",
      "top": 80.49,
      "left": 149.12,
      "attrs": { "color": "green" }
    }
  ],
  "connections": [ [ "uno:GND.1", "led1:C", "black", [ "v0" ] ], [ "uno:5", "led1:A", "green", [ "v0" ] ] ]
}

boisgera / tinygo-arduino Goto Github PK

tinygo-arduino's Introduction

TinyGo for Arduino

🧭 Introduction

📖 Documentation

🧰 Do It Yourself (DIY)

💻 Hello world! (PC/Go version)

💻 Hello world! (PC/TinyGo version)

📟 Hello world! (Arduino/TinyGo version)

⏱️ Time

🚥 Blinky

📄 Intel HEX

💻 WokWi Simulator

🚥 LED

🔲 Toggle Button + LED

📉 ADC

📈 PWM

tinygo-arduino's People

Contributors

Stargazers

Watchers

Forkers

tinygo-arduino's Issues

Recommend Projects

Recommend Topics

Recommend Org