boubounokefalos / ender_sw Goto Github PK

The cad and stl call for m3x30,Printed today and m3x30 is too short
M3x30 wont make it to the stepper motor threads

This part says 1 when 8 are needed. Can we change that

https://github.com/boubounokefalos/Ender_SW/blob/Rev.2/STLS/Misc/2mm_spacer.stl

Just curious as to why the upper idler was changed, this would now require 2 m5x40 rather than 1. If this affects the BOM can you please update.

Love the look especially with the enclosure was looking into doing the conversion on my new Ender3Pro, but don't see any BOM for what can be reused vs what i'm going to have to order do you have one for the project? No XLSX or anything, just sorta got to look at the cad?

Especially for the enclosure parts

On my V2 the cutout is ~40mm (not 35 as this STL expects) ..
it also looks like its been cut out "more"? .. the intended clip in the current design won't catch on anything there ..

See image from interference analysis, the parts don't quite sit straight. There's a leg that needed extending as well that helps keep the parts square. I've made some fixes. https://github.com/strayr/Ender3_switchwire_fixes/tree/main/XZ-blocks.

I've done a T-slost version as well as I didn't want to cut up my ender 3.

I hope this is helpful, I'm not sure if I should be posting issue here or to triano's verion 2?

the skr bracket, mounted as the cad drawing depicts, leaves the USB port too close to the right main 4040 bracket. I do like where its mounted, and looking for a 90 degree usb cable.

Please update the PS_2020_mount_b.stl name. As per CAD it should be PS_4040_mount_b.stl

I just went to install the front grill on my Ender 3 v2 and realized that mine does not have tapped holes for the two outer 4040 extrusions, so I can’t mount the front and rear grills as designed.

I was thinking about modifying the front 4040 extenders so that the front grill bolts to them directly, and then the extenders could slot into the V-slot grooves, but I’m concerned that it won’t be strong enough with the weight of the enclosure and display.

Is it possible to buy new extrusions with the holes already drilled in the right places for mounting the Z profiles and the 4040 that goes between these two? Tapping the holes myself is not something I’m equipped for.

Any guidance on how I should proceed would be appreciated.

Hello.

When is Rev. 2 supposed to be released?

Part appears to be artifact? -

In cad, part is inside the rear end of the y-axis 4040 by 10mm.

If part is needed for full range of motion for bed, then hardware should be updated from M5x0.8x16 BHCS to M5x0.8x25 BHCS. However, this will offset the rear grills 10mm and prevent the rear middle grill from mounting as is.

As the title says, I want to ask if its possible to Switchwire the Ender 3 V2 Neo.

I want to do the conversion and watched trough the STL files. Whats the diffrence between the Parts with [a] at beginning an the parts without and which one do i need to print? I want to do the conversion on a Ender 3 Pro.

Hi i love your work and actaually working my way through the conversion as we speak. I notice that the board you support skr mini e3. But i have skr 3 board. Was wondrring if you can help me out?

I can't find anything about mounting the printed parts to the enclosure. Is the tape used here?

Hello, can someone add support for Orange pi 3 LTS for mounting?

Is something wrong with my Ender 3 Pro or I missed something? I printed all elements but it doesn't fit to my Y axis. It looks like my Ender 3 has a different construction and the frame profile is slightly moved to the end. It causes some issues because I can't mount the step motor and the rest of the elements.

https://photos.app.goo.gl/wZVkKsc1fxiVbf6e9
https://photos.app.goo.gl/VmHkx89yoPZ2q3Ks9

Can you tell me where the BOM is or the link?

Is this compatible with the original Ender 3? I think the big issue will be the 40x40 extrusion on the Y, right?

Some of the links in the Wiki Docs are incorrect. They have STLS in the path when it should be STL as an STLS folder doesn't exists in this repository,

During the build process of my Voron 2.4 i found the rail alignment tool invaluable to get proper alignment on the aluminium extrusions. Would be nice to have that tool for this project too (one that fits on the 4040 extrusion for the y axis to enable correct alignment)

since the ender 3 has warping problems with the bed can you add support for the mk52 bed

Hi, I dont have access to genuine Omron Probe. I was look to use a clicky probe like quickdraw or Klicky probe. Do you have any working option for clicky probe? or can it be desinged around this conversion?

Hi. I have a Ender 3v2. The cutout in the frame is 40x40mm.This file is 35x40. Can you add 40x40 ?

Hi, thanks so much for your awesome work on this!

I'm opening this issue because when searching through the .f3d file I can't seem to find any screws attaching the feet to the frame. I assume since the extensions are 20mm tall that we probably want something like M5x25 or 30mm but I couldn't tell. Do you have a particular screw spec'd for this part?

About to order my screws for the build and want to be sure I grab em all :)

The spacers in the switchwire conversion CAD are 5.2mm ID 8mm OD 8.3mm long. The spacers in the switchwire BOM are 6 x 6 x 3 stainless steel.

Are the spacers in the CAD the silicone ones?

It would be nice if you could create a DXF file for the deck panels (preferably in the same two piece configuration as the stock SW) so they could be laser cut?

The BOM page in the wiki should note that a 5th MGN12 rail is needed for this conversion, since the official BOM for the Switchwire only requires 4.

I'd submit a pull request for it.... but you know, can't do PRs on the wiki repo. Thanks GitHub.

It shows as 4x m3x12mm for assembling the case, too short and I had to go for 16s, same with the display case to the grill 2x m3x12, has to be 16s.

I would really like to make the conversion, but without a conversion, it feels kind of weird.
At first, i thought i would buy the entire sw bom, without the extrusions, psu, mainboard, hotend and rpi, but I'm assuming some of the screws can be conserved, and some stuff need to be adapted to the extrusion size of the ender 3 pro. So is there a complete BOM for this ?

Hi! I've realised that M5x10 SHCS is a non-Voron BOM spec screw but its missing from the wiki, I had to order some midway building as i couldn't assemble my Y idler and motor, hope you can help add in the wiki for others!

I would love to do this conversion, but on a original ender 3 not the V2, is this possible?

Seems like the model calls for a 310mm X gantry extrusion .. seems like my Ender 3 v2 uses a 350mm one there.

I'm reluctant to cut it (since once its done there is no going back there ;) .. really gotta get all my parts assembled and ready before I do this next step .. was hoping I was going to be able to be a bit gradual, but this one part seems to require a permanent modification.
It seems like the whole design depends on that extrusion being a but shorter than its wide so it seems like its kind of key to note that for folks.

The instructions should include something about potentially needing to do this :)

Perhaps in the wiki around the frame section.

Where is the BOM? I cannot find it anywhere in the files. Thank you.

Yours :

Official CAD from VoronDesign :

small thing many thanks for the great CAD and STL's it's a delight so far!

i was just scratching my head figuring out where that endstop was...

Hello,
Is there a way to reach you via Discord or something like that? I have a few ideas for Rev. 2.

Might need to reverse the center space or flip the recessed holes

Please correct usage of default parameter values in cancel_print and pause
like this:
#default_parameter_X: 220
#default_parameter_Y: 220
#default_parameter_Z: 10
gcode:
{% set X = params.X|default(220) %}
{% set Y = params.X|default(220) %}
{% set Z = params.X|default(10) %}

Hi can you add the whole plates from the buttom , for lasercutting ind dfx files pls.

missing CAD files for stock Ender 3 screen

Any plan could use CR6 SE upgrade to Voron Switchwire like?
I have one CR6 SE not use for long time... too slow compare to my voron 0.2

Hi everyone, it's a shame that this doesn't exist for CR10.

because I have a cr10 v1 lying around it would have been nice to transform it into voron switchwire

Viewing the dxf panel bottom_panel.dxf it appears out of date with the current CAD drawing. It only shows 1 screw hole when the design calls for more. I haven't checked the exact dimensions for the other panels but are they up to date with the current design? I want to send them off to Sendcutsend but ran in to this issue.

Thanks! Appreciate all the work on this.

the y stop bracket doesnt account for the solder on the back side of the switch board. the fix would be to put the cutout hole that's on the side that faces the 4040 on the side that faces the board instead.. I mean the board fits perfectly on the other side, like that cutout was meant to accomodate the back side of the board, but the screw countersinks that are used to mount the bracket to the 4040 are on the other side of the cutout. or just make that cutout go all the way through, the part doesnt go through a lot of stress.

4040 rail tool.zip

Will this conversion work on a Voxlab Aquila? Its very similar to an Ender 3 V2, just a different mainboard (which I am planning on swapping out anyway) and the stock screen is sideways instead of vertical like on the Ender 3 V2.

I modified and created a remix for the Y carriage to allow for the Ender 3 Max and CR10 plates wasn't sure where to contact or upload it.

I'll be doing a bunch more mods to adapt it and will keep the files contained as the build goes forward for you future uploads.

https://www.printables.com/model/340607-voron-switchwire-ender-3-max-and-cr10-y-adapter-fo