ciegyet / histblinuxv100r005c00spc050 Goto Github PK
View Code? Open in Web Editor NEWThis project forked from jasonfreelab/histblinuxv100r005c00spc050
Hisilicon SDK for SoC Hi3798Mv100 / Hi3798Cv200 / Hi3798Mv200 / Hi3798Mv300.
This project forked from jasonfreelab/histblinuxv100r005c00spc050
Hisilicon SDK for SoC Hi3798Mv100 / Hi3798Cv200 / Hi3798Mv200 / Hi3798Mv300.
Term: $sdk_path: SDK code path $chip_type: chip type $out_dir: the path of output files after building the SDK 1. For SDK usage and development environment building,please refer <Linux Development Environment User Guide> for detail. 2. Compile SDK 2.1 "source $sdk_path/env.sh" must be executed before compiling the SDK. 2.2 "cp configs/$chip_type/xx_cfg.mak cfg.mak" can use to config the SDK before compile it. customer can customize the SDK configuration by "make menuconfig". 2.3 Customer can get usage information of compiling command by execute "make help" . Notes: SDKs support multi-threaded compilation, but when compiling SDKs on virtual machines or servers with lower performance, it is recommended that single-threaded compilation be conducted or the number of compilation threads be designated. Single-threaded compilation: make $target; two-threaded compilation: make $target -j 2. 3. Burn the board 3.1 Use the "HiTool" to burn the board is recommended. 3.2 Command in boot console also be supported to burn the board. below gives the demonstration . NAND flash: For example(the value should be modified according to chipset and board): mw.b 1000000 ff 80000 tftp 1000000 fastboot-burn.bin nand erase 0 100000 nand write 1000000 0 80000 SPI flash: sf probe 0 mw.b 1000000 ff 80000 tftp 1000000 fastboot-burn.bin nand erase 0 100000 sf write 1000000 0 80000 eMMC flash: The commands for the eMMC flash are as follows: Help command: help mmc Read command : mmc read 0 ddroffset startblock blockcount Write command: mmc write 0 ddroffset startblock blockcount [Note] ---The eMMC flash is read or written by block. A block has 512 bytes. ---The eMMC flash uses the ext4. ---Burning images by using the command line on the eMMC flash is too complex. The HiTool is recommended. 4. Customize bootargs 4.1 The default bootargs.bin will be generate in $out_dir/image/ according to the bootargs_xx.txt . bootargs_xx.txt is in $sdk_path/configs/$chip_type/prebuilts (this path may change in future ,customer can execute "find . -name bootargs* " in $sdk_path/configs to search it) 4.2 For bootargs customize, customer can directly modify the bootargs_xx.txt ,then use the command "mkbootargs" to generate the bootargs.bin. below gives a demonstration: mkbootargs -s 128k -r bootargs.txt -o bootargs.bin 4.3 Customer also can set bootargs directly in boot console. such as(the parameter should be modified by customer): setenv bootcmd 'nand read 1000000 c00000 800000;bootm 1000000' setenv bootargs 'mem=1G console=ttyAMA0,115200 root=/dev/mtdblock5 rootfstype=yaffs2 mtdparts=hi_sfc:1M(boot);hinand:4M(baseparam),4M(pqparam),4M(logo),8M(kernel),96M(rootfs),-(others) mmz=ddr,0,0,300M' saveenv 4.4 For more detail ,please refer to <Linux Development Environment User Guide>. 5. Mounting the NFS and Debugging Programs 5.1 Config the board network use command: udhcpc or ifconfig eth0 hw ether 00:xx:xx:xx:xx:xx; ifconfig eth0 xxx.xxx.xxx.xxx netmask 255.255.xxx.0;route add default gw xxx.xxx.xxx.x; 5.2 Mount the NFS. mount -t nfs -o nolock -o tcp xxx.xxx.xxx.xxx:/xxx/$sdk_dir /mnt 5.3 Add the path for searching dynamic library files: /mnt/$out_dir/lib/share/. export LD_LIBRARY_PATH="/mnt/$out_dir/lib/share/:$LD_LIBRARY_PATH" 5.4. Replace the .ko file. cd /mnt/$out_dir/kmod rmmod xxx.ko insmod xxx.ko 5.5 Run the sample. cd /mnt/$out_dir/obj/sample/ ./sample_xxx 6. Mounting a USB device 6.1 Load the .ko files. insmod ehci-hcd.ko insmod ohci-hcd.ko If the NTFS is to be supported, load ufsd.ko. insmod ufsd.ko 6.2 Mount the USB device. If the FAT32 is used, run the following command: mount -t vfat /dev/sda /usb If the NTFS is used, run the following command: mount -t ufsd /dev/sda /usb 7. SDK developing and debug, please refer to <HMS Development Guide> and <HMS Debugging Guide> 8. HiLoader: please refer to <HiLoader Development Guide> 9. CAS : please refer to <Advanced CA Development Guide>
A declarative, efficient, and flexible JavaScript library for building user interfaces.
๐ Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. ๐๐๐
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google โค๏ธ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.