BBQX0KBD is an I2C Keyboard Device Driver for keyboard devices made by Solder Party. The following keyboards are currently supported by this driver:

1. BB Q10 Keyboard PMOD
2. Keyboard FeatherWing
3. BBQ20KBD

The current version supports the devices as Console Keyboards only, the desktop GUI usage has minor issues.

The drivers are named so (with an 'X'), so as to support future products by the original creator. The driver is mainly developed and tested on the following SBCs from Raspberry Pi Foundation's

1. Raspberry Pi Zero W
2. Raspberry Pi Zero 2 W
3. Raspberry Pi 3 Model B.

The original source code by arturo182, is a good starting point from where this driver builds on. This driver offers the following features:

• Ability to use the keyboard without needing an extra Interrupt Signal.
• Ability to use lower and upper case letters.
• Ability to use SYM Key on Keyboard as Right Alt (or Alt Gr).
• Caps Lock and Num Lock.
• Control Keyboard and Screen* Brightness from key presses.
• Ability to assign different functionality to trackpad, either as a mouse or a single Home Button.**
• Control Volume from key presses.***
• Software shutdown of keyboard and screen backlights when driver is removed.
• Minimum effort to change I2C Peripheral address for Keyboard.

*Available only on Keyboard FeatherWing for now.

**Available only on BBQ20KBD for now.

***Not tested this feature 100%.

The keyboard layout is shown below.

The top row is unique to the Keyboard FeatherWing, while the BBQ20KBD has a similar top key row, with the essential difference that it uses a trackpad instead of 5-way key. Even then, except for the CTRL Key, every other keypress on this row can be executed from the keyboard/BB Q10 Keyboard PMOD module itself.

By default, each key on the keyboard itself signifies the middle element mentioned in the layout below.

To access the keys mentioned above a character, press and hold LFTALT (Left alt) and press the desired key. For example, Key(/) is presented by LFTALT+G.

To access the keys mentioned below a character, press and hold RTALT (Right alt) and press the desired key. For example, Key(=) is presented by RTALT+I.

Upper Case Letters can be executed by pressing LEFT_SHIFT + the key.

Caps Lock is toggled by pressing LFTALT + LEFT_SHIFT.

Num Lock is toggled by pressing LFTALT + RIGHT_SHIFT.

Screen Brightness can be increased or decreased by RTALT+Q and RTALT+W respectively. Toggling the same is done by RTALT+S.

Keyboard Brightness can be increased or decreased by RTALT+K and RTALT+L respectively. Toggling the same is done by RTALT+$.

Volume can be increased or decreased by RTALT+Z and RTALT+X respectively. Muting the same is done by RTALT+~.

 *		   BBQ10KBD PMOD KEYBOARD LAYOUT
 *
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|#     |1    |2   |3   |(   |   )|_   |    -|    +|      @|
 *	|  Q   |  W  | E  | R  | T  |  Y |  U |  I  |  O  |   P   |
 *	|    S+|   S-|PgUp|PgDn|   \|UP  |^   |=    |{    |}      |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|*     |4    |5   |6   |/   |   :|;   |    '|    "|    ESC|
 *	|  A   |  S  | D  | F  | G  |  H |  J |  K  |  L  |  BKSP |
 *	|     ?|   Sx|   [|   ]|LEFT|HOME|RGHT|V+   |V-   |DLT    |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|      |7    |8   |9   |?   |   !|,   |    .|    `|       |
 *	|LFTALT|  Z  | X  | C  | V  |  B |  N |  M  |  $  | ENTER |
 *	|      |   K+|  K-|   °|   <|DOWN|>   |MENU |Vx   |       |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|            |0   |TAB                |     |             |
 *	| LEFT_SHIFT | ~  |       SPACE       |RTALT| RIGHT_SHIFT |
 *	|            |  Kx|                  &|     |             |
 *	+------------+----+-------------------+-----+-------------+
 *

 *		BBQ10KBD FEATHERWING KEYBOARD LAYOUT
 *
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|      |          |        UP         |           |       |
 *	| Ctrl |   PgDn   |  LEFT HOME RIGHT  |   PgUp    | MENU  |
 *	|      |          |       DOWN        |           |       |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|                                                         |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|#     |1    |2   |3   |(   |   )|_   |    -|    +|      @|
 *	|  Q   |  W  | E  | R  | T  |  Y |  U |  I  |  O  |   P   |
 *	|    S+|   S-|PgDn|PgUp|   \|UP  |^   |=    |{    |}      |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|*     |4    |5   |6   |/   |   :|;   |    '|    "|    ESC|
 *	|  A   |  S  | D  | F  | G  |  H |  J |  K  |  L  |  BKSP |
 *	|     ?|   Sx|   [|   ]|LEFT|HOME|RGHT|V+   |V-   |DLT    |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|      |7    |8   |9   |?   |   !|,   |    .|    `|       |
 *	|LFTALT|  Z  | X  | C  | V  |  B |  N |  M  |  $  | ENTER |
 *	|      |   K+|  K-|   °|   <|DOWN|>   |MENU |Vx   |       |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|            |0   |TAB                |     |             |
 *	| LEFT_SHIFT | ~  |       SPACE       |RTALT| RIGHT_SHIFT |
 *	|            |  Kx|                  &|     |             |
 *	+------------+----+-------------------+-----+-------------+
 *

 *	               BBQ20KBD PMOD KEYBOARD LAYOUT
 *
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|      |          |BR     ↑TPY-       |           |       |
 *	| Ctrl |   PgDn   |←TPX- BL(HOME)TPX+→|   PgUp    | MENU  |
 *	|      |          |       ↓TPY+       |           |       |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|                                                         |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|#     |1    |2   |3   |(   |   )|_   |    -|    +|      @|
 *	|  Q   |  W  | E  | R  | T  |  Y |  U |  I  |  O  |   P   |
 *	|      |     |PgDn|PgUp|   \|UP  |^   |=    |{    |}      |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|*     |4    |5   |6   |/   |   :|;   |    '|    "|    ESC|
 *	|  A   |  S  | D  | F  | G  |  H |  J |  K  |  L  |  BKSP |
 *	|     ?|     |   [|   ]|LEFT|HOME|RGHT|V+   |V-   |DLT    |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|      |7    |8   |9   |?   |   !|,   |    .|    `|       |
 *	|LFTALT|  Z  | X  | C  | V  |  B |  N |  M  |  $  | ENTER |
 *	|      |   K+|  K-|   °|   <|DOWN|>   |MENU |Vx   |       |
 *	+------+-----+----+----+----+----+----+-----+-----+-------+
 *	|            |0   |TAB                |     |             |
 *	| LEFT_SHIFT | ~  |       SPACE       |RTALT| RIGHT_SHIFT |
 *	|            |  Kx|                  &|     |             |
 *	+------------+----+-------------------+-----+-------------+
 *

• Software Pre-requisites

  1. The Raspberry Pi must have kernel drivers installed on it.

     sudo apt install raspberrypi-kernel-headers

  2. The Pi must have its I2C Peripheral enabled. Run sudo raspi-config, then under Interface Options, enable I2C.

• Hardware Pre-rquisties: Keyboard to Raspberry Pi Hardware connections. 0. If using the keyboard without interrupt pin (How to do so is discussed below under Installation Options), make the following connections: 3.3V on Pi --> 3.3V on Keyboard Module. GND on Pi --> GND on Keyboard Module. SCL(Pi Pin 5/BCM GPIO 3) on Pi --> SCL on Keyboard Module. SDA(Pi Pin 3/BCM GPIO 2) on Pi --> SDA on Keyboard Module.

  1. If Interrupt Pin is used, the pin is identified from the BCM Pin Number and not the Raspberry Pi GPIO Pin number.

  Check pre-requisites with the command i2cdetect -y 1(one might need sudo). They keyboard should be on the address 0x1F. If you are using the Keyboard FeatherWing, the Touch sensor on the screen will also show up on 0x4B.

Copy the Git repository from above and download it on your Pi, preferably on /home/pi/ using the below command and change in to the folder.

git clone https://github.com/wallComputer/bbqX0kbd_driver.git
cd bbqX0kbd_driver/

• To install the files with default configurations, use the installer.sh file.

  ./installer.sh --OPTION VALUE

  Where --OPTION is valid configuration option discussed below.
• To remove, use the remover.sh file.

  ./remover.sh

The installation script installer.sh has multiple options. The description of these can be accessed by -h or --h option as below

  ./installer.sh -h

The following options are available:

• --BBQX0KBD_TYPE : Keyboard Version You want to build kernel driver for. Available Options:
  1. BBQ10KBD_PMOD
  2. BBQ10KBD_FEATHERWING
  3. BBQ20KBD_PMOD (Default)
• --BBQ20KBD_TRACKPAD_USE : Use BBQ20KBD_PMOD's trackpad either as a mouse, or as KEY_HOME. Availabe Options:
  1. BBQ20KBD_TRACKPAD_AS_MOUSE (Default)
  2. BBQ20KBD_TRACKPAD_AS_KEYS
• --BBQX0KBD_INT : Build a driver that uses the external Interrupt Pin, or build one without it, polling the Keyboard instead. Available Options:
  1. BBQX0KBD_USE_INT
  2. BBQX0KBD_NO_INT (Default)
• --BBQX0KBD_INT_PIN : Raspberry Pi BCM Pin Number for the Interrupt Pin. Default value is 4. Note that BCM Pin Numbers are different from Pi's header Pin Numbers.
• --BBQX0KBD_POLL_PERIOD : Polling Rate for the Keyboard in milliseconds. Value between 10 to 1000. Defualt is 40.
• --BBQX0KBD_ASSIGNED_I2C_ADDRESS : I2C Address if changed. Default Value is 0x1F.

The following examples may be useful:

./installer.sh

This is the default option. It creates a Keyboard Driver for BBQ20KBD on I2C Address 0x1F. The Keyboard does not need Int Pin and instead polls the Keyboard every 40ms. The trackpad is used as a mouse, and the button is used as mouse left click. On pressing the button with Left Alt as LFTALT + BTN_LEFT, a mouse right key is registered.

./installer.sh --BBQX0KBD_TYPE BBQ10KBD_FEATHERWING --BBQX0KBD_INT BBQX0KBD_NO_INT --BBQX0KBD_POLL_PERIOD 25

This creates the kernel driver for Keyboard Featherwing. It does not use the Interrupt Pin, instead polls the keyboard every 25ms.

./installer.sh --BBQX0KBD_TYPE BBQ10KBD_PMOD --BBQX0KBD_INT BBQX0KBD_USE_INT --BBQX0KBD_INT_PIN 23

This creates the kernel driver for BBQ10KBD_PMOD. It does use the Interrupt Pin, namely, BCM Pin GPIO 23 (Pin 16 on the header).

./installer.sh --BBQX0KBD_TYPE BBQ20KBD_PMOD --BBQX0KBD_INT BBQX0KBD_NO_INT --BBQX0KBD_ASSIGNED_I2C_ADDRESS 0x45

This creates the kernel driver for BBQ20KBD_PMOD. The Driver assumes the Keyboard is available on I2C Address 0x45, as well as polls it at default poll rate of 40ms.

./installer.sh --BBQX0KBD_TYPE BBQ20KBD_PMOD --BBQ20KBD_TRACKPAD_USE BBQ20KBD_TRACKPAD_AS_KEYS

This creates the kernel driver for BBQ20KBD_PMOD and uses the trackpad as KEY_HOME. The Mouse movement is not registered.

After following guide, reboot your pi and on login, the Keyboard should be working on /dev/tty1. To view the above console, Use an LCD such as the one on the Keyboard FeatherWing, or any other you can get to work with your Pi. The easiest way is to either use a Adafruit PiTFT, or use the below example of using juj's frcp-ili9341 project.

###(Optional) Setting Up a Screen with the Keyboard Module

Keyboard FeatherWing has an ILI9341 on it. Using it for the main console can be of great use. The below steps describe how to connect and control this LCD from the Pi.

1. Hardware connections

   3.3V on Pi ----> 3.3V on Keyboard FeatherWing.
   GND on Pi -----> GND on Keyboard FeatherWing.
   SCLK(Pi Pin 23/BCM GPIO 11) ---> SCK on Keyboard FeatherWing.
   MOSI(Pi Pin 19/BCM GPIO 10) ---> CO on Keyboard FeatherWing.
   CE0(Pi Pin 24/BCM GPIO 8) ---> LCD_CS on Keyboard FeatherWing.
   GPIO9(Pi Pin 13/BCM GPIO 27) ---> LCD_DC on Keyboard FeatherWing.

   If you are using the Keyboard FeatherWing, you will also need to pull the RST Pin on the Featherwing to 3.3V.

   3.3V on Pi ----> RST on Keyboard FeatherWing.

2. Install git and cmake.

   sudo apt install git cmake

3. Clone juj's project, and create a directory build inside it, and change in to it.

   git clone https://github.com/juj/fbcp-ili9341.git
   cd fbcp-ili9341
   mkdir build
   cd build/

4. Inside the build directory, run the below cmake command.

   cmake -DILI9341=ON -DSPI_BUS_CLOCK_DIVISOR=40 -DGPIO_TFT_DATA_CONTROL=27 -DSTATISTICS=0 ..

5. Run a make command as

   make -j

6. The result of the above file will be a fbcp-ili9341 file. Place the absolute path of this file in the last line but one of /etc/rc.local as below (assuming the absolute path is correct)

   sudo /home/pi/fbcp-ili9341/build/fbcp-ili9341 &

7. Place the below text in /boot/config.txt

   hdmi_group=2
   hdmi_mode=87
   hdmi_cvt=320 240 60 1 0 0 0
   hdmi_force_hotplug=1

8. From sudo raspi-config, under System Options, set the Boot / Auto Login feature to Console or Console Autologin.
9. Reboot.
10. On boot up, the LCD should start showing console. It might be useful to run sudo dpkg-reconfigure console-setup (can be done over ssh), choose the desired font and size, and place a sudo /etc/init.d/console-setup.sh reload & in the /etc/rc.local file just as in step 5.

• The Settings of the LCD can be changed as shown in fbcp-ili9341. Notably, the Data_Command Pin can be changed and Clock speed can be increased.
• Look at the bbqX0kbd.map file for alternate key binds. Edit it as per your need and put the new map file in correct folder (as per installer.sh) to be loaded correctly in /etc/default/keyboard. One can use sudo loadkeys path/to/bbqX0kbd.map while the driver is running, and press keys to check their new key bindings before placing it in the right location. Once satisfied with your keymap, run ./remover.sh && ./installer.sh to reinstall everything correctly.

• The BIGGEST FLAW at the moment is that the driver does not work as intended on Desktop view. The basic keys work, so do Num Lock and Caps Lock features. However, the mapping assigned as per the above keyboard layout does not present itself. Pressing the LFTALT key immediately presents the alternate optional menus, which hinders getting any higher and lower keys as per the layout. Two things are suspected, either the Buster Keyboard Layout configuration has some issues (Buster has had issues in Keyboard config for me from raspi-config, or else it's as intended behaviour, Alt Key pressed on a GUI indicates using other keys for menu options and not for printing characters.
• RTALT+$ (or the Volume Key on BBQ20KBD) produces MUTE Key. However on Console, it also puts out the ~ key. I have not yet been able to find the cause of this issue.
• The entire feature of Volume control is untested as of now. evtest shows the Volume Up, Volume Down, and MUTE keys pressed, but as the keyboard driver works the best on console only at the moment, I'm not sure how this function works on a Desktop GUI.
• On first boot, RTALT+G or RTALT+J presents other tty options one can log in to, and the RTALT+Y, RTALT+H, and RTALT+B do not produce the desired keys too . This behaviour is found only on first boot after installing the driver, never after and the keyboard works fine from there on.
• Rarely, the keyboard often becomes unresponsive and does not appear on the I2C Bus for extended period of time. The only solution becomes to shutdown the Pi completely (often with the need to remove power). I do not know if this is a driver issue or hardware issue, and I have not been able to replicate it often. If you are able to replicate it, please let me know and I'll try my best to solve it in code.

• Move the fifo reading task to a work queue. This will require changes in a few places, though the core logic should not change. [DONE: using delayed_work_branch]
• Solve the BIGGEST FLAW
• Make the code compatible with upcoming works of Solder Party Keyboards.
• Add The touch screen sensor to Keyboard Driver itself.
• Add Pimoroni trackball to be used as single press mouse to the screen and keyboard. [Done: using different kernel driver.]
• Solve other design flaws.
• Use the Neopixel on the Keyboard FeatherWing as well as the Ambient light sensor (if possible for the latter with some cheap single channel ADC.
• Create a PCB to make the design modular and compact.

Pull requests are welcome.

• arturo182 & Solder Party for the amazing product. Please buy more of their new awesome stuff and join their discord for amazing upcoming stuff.
• juj's frcp-ili9341 project for making small size screens so easy to use!

The code itself is LGPL-2.0 though I'm not going to stick it to you, I just chose what I saw, if you want to do awesome stuff useful to others with it without harming anyone, go for it and have fun just as I did.