Broken DTMF calling (`D Decd`) about uv-k5-firmware-custom HOT 14 CLOSED

Radio with D Decd set to ON should have no sound on receive, unless you call it with its ANI ID. When I call my radio with 102*103 I get the sound.

https://github.com/egzumer/uv-k5-firmware-custom/wiki/Radio-operation#dtmf-calling-decoding

I understand. I'm very sorry for wasting a lot of your energy and time.Thank you very much for everything you selflessly did for K5！

from uv-k5-firmware-custom.

DTMF decoding is originally meant to give an option to call each other somewhat like with phones. The call pattern is
callee*caller
Where callee and caller are 3 digit ANI ID of each radio. If radio receives a call it only then starts to listen for a preset amount of time.
This was broken in 1o11's repo when I forked it. I will try to fix that in the future.

from uv-k5-firmware-custom.

DTMF decoding is originally meant to give an option to call each other somewhat like with phones. The call pattern is Where callee and caller are 3 digit ANI ID of each radio. If radio receives a call it only then starts to listen for a preset amount of time. This was broken in 1o11's repo when I forked it. I will try to fix that in the future.callee*caller

same issues still exists

from uv-k5-firmware-custom.

You didn't actually say what is the problem, you only described what is going on. So what is the actual problem?

from uv-k5-firmware-custom.

You didn't actually say what is the problem, you only described what is going on. So what is the actual problem?

Yes, I only know the phenomenon of the problem. I don't understand programming, and of course I don't know where the problem lies

from uv-k5-firmware-custom.

No, not where the problem lies, I will investigate where it lies, but you didn't state the problem at all.

from uv-k5-firmware-custom.

No, not where the problem lies, I will investigate where it lies, but you didn't state the problem at all.

I told you the method of reproduction. What's not clear about it

from uv-k5-firmware-custom.

You only described what you do, you didn't state what is not right in the result.

from uv-k5-firmware-custom.

I fixed what I consider wrong, but you say it is still the same so I'm getting confused

from uv-k5-firmware-custom.

No, not where the problem lies, I will investigate where it lies, but you didn't state the problem at all.

Two k5s, A is the quansheng original firmware, B is your firmware today.
both same freq （eg438.500）, both with DTMF (D Decd) turned on. After this setting
Result B calls A , A only light No sound,
A calls B，B only light No sound

from uv-k5-firmware-custom.

I fixed what I consider wrong, but you say it is still the same so I'm getting confused

Wait a few minutes, I will send the video to the telegram

from uv-k5-firmware-custom.

Can you see any "bad", "wrong", "not right", "error", "not expected" in your statement? Because I don't. How am I supposed to ask the question in any other way?

You do certain actions, and you get certain outcome. Can you state what is different in what is happening from what you expect to happen?

from uv-k5-firmware-custom.

Can you see any "bad", "wrong", "not right", "error", "not expected" in your statement? Because I don't. How am I supposed to ask the question in any other way?

You do certain actions, and you get certain outcome. Can you state what is different in what is happening from what you expect to happen?

I opend D decd and press PTT to other，They have no sound，I think D decd has something wrong
Open dtmf The receiver cannot output sound

from uv-k5-firmware-custom.

Radio with D Decd set to ON should have no sound on receive, unless you call it with its ANI ID. When I call my radio with 102*103 I get the sound.

https://github.com/egzumer/uv-k5-firmware-custom/wiki/Radio-operation#dtmf-calling-decoding

from uv-k5-firmware-custom.