This repository contains assorted example projects for the 1Bitsy development platform.

To be able to compile the examples included in this repository you will require an arm-none-eabi gcc toolchain. We recommend you install the gcc-arm-embedded toolchain that is being maintained by ARM. The downloads and installation instructions for Linux (Ubuntu), Mac OS X and Windows can be found on the gcc-arm-embedded Launchpad page.

You must run make in the top level directory first. This builds the library and all examples. If you're simply hacking on a single example after that, you can type make clean; make in any of the individual project directories later.

For more verbose output, to see compiler command lines, use make V=1 For insanity levels of verboseness, use make V=99

The makefiles are generally usable for your own projects with only minimal changes for the libopencm3 install path (See Reuse)

If you are using an older GCC compiler (pre V5) you may need to specify the C standard, otherwise the compiler might complain. To solve this issue you can invoke make in the top level directory while setting the CFLAGS variable:

CFLAGS=-std=c99 make

To flash the 'miniblink' example to the 1Bitsy (after running make in the top-level directory), you can execute:

cd examples/1bitsy/miniblink
make flash

The Makefiles for the examples are configured to use a Black Magic Probe by default, and it will list the serial ports that it found for you to choose from.

If you don't want to choose from a list, you can provide the serial port directly to the target by invoking:

cd examples/1bitsy/miniblink
make flash BMP_PORT=/dev/ttyACM0

You can also use dfu-util to upload the selected firmware by running:

cd examples/1bitsy/miniblink
make dfu-flash

You can also flash manually using a myriad of different tools depending on your setup. Here are a few examples.

cd examples/1bitsy/fancyblink
arm-none-eabi-gdb miniblink.elf
target extended-remote /dev/ttyACM0
monitor swdp_scan
attach 1
load
run

To exit the gdb session type <Ctrl>-C and <Ctrl>-D. It is useful to add the following to the .gdbinit to make the flashing and debugging easier:

set target-async on
set confirm off
set mem inaccessible-by-default off
#set debug remote 1
tar ext /dev/ttyACM0
mon version
mon swdp_scan
att 1

Having this in your .gdbinit boils the flashing/debugging process down to:

cd examples/1bitsy/fancyblink
arm-none-eabi-gdb miniblink.elf
load
run

If you put your 1Bitsy in DFU Bootloader mode (shorting the DFU Bootloader jumper while you plug in the USB cable, for example) you will be able to use the following command to upload your firmware:

cd examples/1bitsy/fancyblink
make fancyblink.bin
sudo dfu-util -d 0483:df11 -c 1 -a 0 -s 0x08000000:leave -D fancyblink.bin

For this to work you will need dfu-util V0.8 or newer!

If you want to use any of the code found here in your own project, this examples repository shows the general way. There is also a 1bitsy-locm3-template repository that can serve as a basis for your project.

1. Create an empty repository

mkdir mycoolrobot && cd mycoolrobot && git init .

2. Add libopencm3 as a submodule

git submodule add https://github.com/libopencm3/libopencm3

3. Grab a copy of the basic rules

These urls grab the latest from the libopencm3-examples repository.

wget \
  https://raw.githubusercontent.com/libopencm3/libopencm3-examples/master/examples/rules.mk \
  -O libopencm3.rules.mk

4. Grab a copy of the target Makefile

In this case, we want STM32F4.

wget \
  https://raw.githubusercontent.com/libopencm3/libopencm3-examples/master/examples/stm32/f4/Makefile.include \
  -O libopencm3.target.mk

5. Edit paths in libopencm3.target.mk

Edit the last line of libopencm3.target.mk and change the include to read include ../libopencm3.rules.mk (the amount of .. depends on where you put your project in the next step).

6. Beg/borrow/steal an example project

For sanity's sake, use the same target as the makefile you grabbed above.

cp -a \
  somewhere/libopencm3-examples/examples/stm32/f4/stm32f4-discovery/miniblink \
  myproject

Add the path to OPENCM3_DIR, set the right DEVICE and modify the path to the makefile include:

diff -u
--- Makefile.orig       2017-06-11 12:42:25.378248089 +0200
+++ Makefile    2017-06-11 12:46:42.566244271 +0200
@@ -19,7 +19,8 @@

BINARY = miniblink
 
-DEVICE=STM32F407VG
+OPENCM3_DIR = ../libopencm3
+DEVICE = STM32F415RGT6

-include ../../Makefile.include
+include ../libopencm3.target.mk

You're done :)

You need to run make inside the libopencm3 directory once to build the library, then you can just run make/make clean in your project directory as often as you like.