Hyprpaper is a blazing fast wallpaper utility for Hyprland with the ability to dynamically change wallpapers through sockets. It will work on all wlroots-based compositors, though.
- Per-output wallpapers
- fill or contain modes
- fractional scaling support
- IPC for blazing fast wallpaper switches
- preloading targets into memory
Arch Linux: pacman -S hyprpaper
git clone https://github.com/hyprwm/hyprpaper
cd hyprpaper
make all
the output binary will be in ./build/
, copy it to your PATH, e.g. /usr/bin
On OpenSUSE:
sudo zypper install ninja gcc-c++ wayland-protocols-devel Mesa-libGLESv3-devel file-devel
Hyprpaper is controlled by the config, like this:
~/.config/hypr/hyprpaper.conf
preload = /path/to/image.png
#if more than one preload is desired then continue to preload other backgrounds
preload = /path/to/next_image.png
# .. more preloads
#set the default wallpaper(s) seen on inital workspace(s) --depending on the number of monitors used
wallpaper = monitor1,/path/to/image.png
#if more than one monitor in use, can load a 2nd image
wallpaper = monitor2,/path/to/next_image.png
# .. more monitors
Preload will tell Hyprland to load a particular image (supported formats: png, jpg, jpeg). Wallpaper will apply the wallpaper to the selected output (monitor
is the monitor's name, easily can be retrieved with hyprctl monitors
. You can leave it empty for a wildcard (aka fallback). You can also use desc:
followed by the monitor's description without the (PORT) at the end)
You may add contain:
before the file path in wallpaper=
to set the mode to contain instead of cover:
wallpaper = monitor,contain:/path/to/image.jpg
A Wallpaper cannot be applied without preloading. The config is not reloaded dynamically.
Preload does exactly what it says. It loads the entire wallpaper into memory. This can result in around 8 - 20MB of mem usage. It is not recommended to preload every wallpaper you have, as it will be a) taking a couple seconds at the beginning to load and b) take 100s of MBs of disk and RAM usage.
Preload is meant only for situations in which you want a wallpaper to switch INSTANTLY when you issue a wallpaper keyword (e.g. wallpaper per workspace)
In any and all cases when you don't mind waiting 300ms for the wallpaper to change, consider making a script that:
- preloads the new wallpaper
- sets the new wallpaper
- unloads the old wallpaper (to free memory)
You can use hyprctl hyprpaper
(if on Hyprland) to issue a keyword, for example
Example:
If your wallpapers are stored in ~/Pictures, then make sure you have already preloaded the desired wallpapers in hyprpaper.conf.
~/.config/hypr/hyprpaper.conf
preload = ~/Pictures/myepicpng.png
preload = ~/Pictures/myepicpngToo.png
preload = ~/Pictures/myepicpngAlso.png
#... continue as desired, but be mindful of the impact on memory.
In the actual configuration for Hyprland, hyprland.conf, variables can be set for ease of reading and to be used as shortcuts in the bind command. The following example uses $w shorthand wallpaper variables:
~/.config/hypr/hyprland.conf
$w1 = hyprctl hyprpaper wallpaper "DP-1,~/Pictures/myepicpng.png"
$w2 = hyprctl hyprpaper wallpaper "DP-1,~/Pictures/myepicpngToo.png"
$w3 = hyprctl hyprpaper wallpaper "DP-1,~/Pictures/myepicpngAlso.png"
#yes use quotes around desired monitor and wallpaper
#... continued with desired amount
With the varibles created we can now "exec" the actions.
Remember in Hyprland we can bind more than one action to a key so in the case where we'd like to change the wallpaper when we switch workspace we have to ensure that the actions are bound to the same key such as...
~/.config/hypr/hyprland.conf
bind=SUPER,1,workspace,1 #Superkey + 1 switches to workspace 1
bind=SUPER,1,exec,$w1 #SuperKey + 1 switches to wallpaper $w1 on DP-1 as defined in the variable
bind=SUPER,2,workspace,2 #Superkey + 2 switches to workspace 2
bind=SUPER,2,exec,$w2 #SuperKey + 2 switches to wallpaper $w2 on DP-1 as defined in the variable
bind=SUPER,3,workspace,3 #Superkey + 3 switches to workspace 3
bind=SUPER,3,exec,$w3 #SuperKey + 3 switches to wallpaper $w3 on DP-1 as defined in the variable
#... and so on
Because the default behavior in Hyprland is to also switch the workspace whenever movetoworkspace is used to move a window to another workspace you may want to include the following:
bind=SUPERSHIFT,1,movetoworkspace,1 #Superkey + Shift + 1 moves windows and switches to workspace 1
bind=SUPERSHIFT,1,exec,$w1 #SuperKey + Shift + 1 switches to wallpaper $w1 on DP-1 as defined in the variable
Since the IPC has to tick every now and then, and poll in the background, battery life might be a tiny bit worse with IPC on. If you want to fully disable it, use
ipc = off
in the config.
You can set splash = true
to enable the splash rendering over the wallpaper.
The value for splash_offset
sets, in percentage, the splash rendering offset relative to the bottom of the display.
If you use a lot of wallpapers, consider unloading those that you no longer need. This will mean you need to load them again if you wish to use them for a second time, but will free the memory used by the preloaded bitmap. (Usually 8 - 20MB, depending on the resolution)
You can issue a hyprctl hyprpaper unload [PATH]
to do that.
You can also issue a hyprctl hyprpaper unload all
to unload all inactive wallpapers.
For other compositors, the socket works like socket1 of Hyprland, and is located in /tmp/hypr/.hyprpaper.sock
(this path only when Hyprland is not running!)