Where do I place the portal html files? I'm assuming on the SD but what folder/s Also ap.config.txt and index.html?

Would it be possible to scale up the main touch target menu elements for easier finger use on the resistive touch screen? I feel like it would be an excellent QoL improvement.

Almost all BLE Spam except sour apple seem to crash pretty quickly. Has anybody found a solution so far?

What GPIO do these map to?

Well, is there a possibility of using Marauder with this one variant? https://a.aliexpress.com/_EvT0DnD

It seems that when entering a rotated menu the screen rotates -90 degrees top counter clockwise but the touch controls rotate 90 degrees so top of unit rotates clockwise... I had to roll back to 0.13.5 where the problem does not exist.
https://youtu.be/UI-ROiRZYok

I want to be able to see battery percentage with tp4056

Flashed bin file using the instructions for esptool. Flash completes but just get blank screen after reset.

I seem to be stuck in a loop. Its probably my fault but any help would be appreciated!

Connecting...
Connected successfully.
Try hard reset.
[Za.readLoop:1] Finished read loop
Error: Couldn't sync to ESP. Try resetting.
Connecting...
Error: Failed to execute 'open' on 'SerialPort': The port is already open.

I plug in, select connect, select my com port through the browser, it says try resetting, I press the reset button screen goes black on the device, and then fails because its already open. Am I just missing something here? I can try a manual run if needed.

the esp32 marauder github repo has analog battery indicator developed by @Joshinken
justcallmekoko/ESP32Marauder#35
justcallmekoko/ESP32Marauder#31
justcallmekoko/ESP32Marauder#30
I want to be able to do that on cyd marauder.

hello,
I can't place the cli commands on the CYD serial port, although I have the startup information.
Firmware version 0.13.9
Thk

Test

hey! what files i need to put on sd card from this project?? please specify them.

Would be awesome to see any form of WPS brute force/pixie attacks implemented

I flashed but screen not seen

The GPS is taking a long time to connect and catch satellites, Sometimes I even reboot several times But it says it's connected.

Is it hard to have this compiling for this board ? ESP32-2432S022c

The platformio board definitions are here https://github.com/rzeldent/platformio-espressif32-sunton/blob/main/esp32-2432S022C.json

Support request for ESP32-8048S043C-I Capacitive Touch Screen 4.3in display

Any chance we can get this working on this display I love the 4.3 in display. Right now not much support for this display besides openhasp

Serial monitor:
08:14:25.207 ->
08:14:25.207 -> Brownout detector was triggered
08:14:25.207 ->
08:14:25.207 -> ets Jul 29 2019 12:21:46
08:14:25.207 ->
08:14:25.207 -> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
08:14:25.207 -> configsip: 0, SPIWP:0xee
08:14:25.254 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
08:14:25.254 -> mode:DIO, clock div:1
08:14:25.254 -> load:0x3fff0030,len:1184
08:14:25.254 -> load:0x40078000,len:13260
08:14:25.254 -> load:0x40080400,len:3028
08:14:25.254 -> entry 0x400805e4
08:14:25.855 -> ESP-IDF version is: v4.4.5
08:14:26.045 -> Using TFT Shield 5
08:14:26.092 -> SPI_FREQUENCY: 40000000
08:14:26.092 -> SPI_READ_FREQUENCY:16000000
08:14:26.092 -> SPI_TOUCH_FREQUENCY: 2500000

For reasons i dont know, the web serial interface you provide cant recognize my cyd on two linux computers.
can you provide the command for esptool to flash the cyd (esp32-wroom)?
I'm not exactly sure; last time i did that with cyd, the process of flashing went well, but the display was black and the backwards LED stayed red...

hi, does this work on the version with capacitive touch?

Best case that holds a stylus?

Can this ESP32 D0WDQ6 be modified with an ipex gain antenna?
PCB antenna performance is terrible

Hello, thanks for sharing this great project/port. I flashed my ESP32-3248S035C with the online flasher everything works RGB LED animation on boot and serial console are both functional however the display stays off is there a version for the larger ESP32-3248S035C ?

I've already put the files in a folder and nothing appears when I call, can someone help me?

Both "deauth targeted" and "deauth flood" seem to not be working.

Following the Justcallmekoko instructions to update using the SD card, it gets hung on rebooting. When rebooting it with the button on the back, the screen goes white and freezes. Is there a way to update to the latest firmware?

Hello everyone.

Does anyone know what should be done to support the 3248s035 device?