Program your Nordic Semiconductor nRF51 or nRF52 board using the Arduino IDE.

Does not require a custom bootloader on the device.

• Plain nRF52 MCU
• Nordic Semiconductor nRF52 DK
  • For boards prior to 2016.9 (see sticker), the lastest JLink bootloader is required to upload sketches. To upgrade, press the boot/reset button while powering on the board and copy over the latest bootloader.
• Shenzhen Taida Century Technology nRF52 low cost development board
• RedBear Blend 2
• RedBear Nano 2

• Plain nRF51 MCU
• BBC micro:bit
• Bluz DK
• Nordic Semiconductor nRF51822 Development Kit + nRF51422 Development Kit
• PCA10000
• PCA10001, PCA10002, PCA10003, PCA10004 via nRF6310(nRFgo)
• Nordic Semiconductor NRF51 Smart Beacon Kit
• Nordic Semiconductor NRF51 Dongle
• OSHChip
• RedBearLab BLE Nano
• RedBearLab nRF51822
• Waveshare BLE400
• ng-beacon
• TinyBLE

1. Download and install the Arduino IDE (At least v1.6.12)
2. Start the Arduino IDE
3. Go into Preferences
4. Add https://sandeepmistry.github.io/arduino-nRF5/package_nRF5_boards_index.json as an "Additional Board Manager URL"
5. Open the Boards Manager from the Tools -> Board menu and install "Nordic Semiconductor nRF5 Boards"
6. Select your nRF5 board from the Tools -> Board menu

NOTE: During installation it takes the Arduino IDE a few minutes to extract the tools after they have been downloaded, please be patient.

No additional setup required.

For 64-bit Linux users, libc6:i386, libstdc++6:i386, libncurses5:i386 and libudev1:i386 need to be installed :

• sudo dpkg --add-architecture i386
• sudo apt-get update
• sudo apt-get install libc6:i386 libstdc++6:i386 libncurses5:i386 libudev1:i386

Download mbed Windows Serial driver

1. Download Zadig
2. Plugin Segger J-Link or DK board
3. Start Zadig
4. Select Options -> List All Devices
5. Plug and unplug your device to find what changes, and select the Interface 2 from the device dropdown
6. Click Replace Driver

NOTE: To roll back to the original driver go to: Device Manager -> Right click on device -> Check box for "Delete the driver software for this device" and click Uninstall

1. cd <SKETCHBOOK>, where <SKETCHBOOK> is your Arduino Sketch folder:

• OS X: ~/Documents/Arduino
• Linux: ~/Arduino
• Windows: ~/Documents/Arduino

2. Create the following directories: tools/nRF5FlashSoftDevice/tool/
3. Download nRF5FlashSoftDevice.jar to <SKETCHBOOK>/tools/nRF5FlashSoftDevice/tool/
4. Restart the Arduino IDE
5. Select your nRF board from the Tools -> Board menu
6. Select a SoftDevice from the Tools -> "SoftDevice: " menu
7. Select a Programmer (J-Link, ST-Link V2, or CMSIS-DAP) from the Tools -> "Programmer: " menu
8. Select Tools -> nRF5 Flash SoftDevice
9. Read license agreement
10. Click "Accept" to accept license and continue, or "Decline" to decline and abort
11. If accepted, SoftDevice binary will be flashed to the board

1. Follow steps from Board Manager section above
2. cd <SKETCHBOOK>, where <SKETCHBOOK> is your Arduino Sketch folder:

• OS X: ~/Documents/Arduino
• Linux: ~/Arduino
• Windows: ~/Documents/Arduino

3. Create a folder named hardware, if it does not exist, and change directories to it
4. Clone this repo: git clone https://github.com/sandeepmistry/arduino-nRF5.git sandeepmistry/nRF5
5. Restart the Arduino IDE

This Arduino Core does not contain any Arduino style API's for BLE functionality. All the relevant Nordic SoftDevice (S110, S130, S132) header files are included build path when a SoftDevice is selected via the Tools menu.

• BLEPeripheral
  • v0.3.0 and greater, available via the Arduino IDE's library manager.
  • Supports peripheral mode only.

If the selected board has an external 32 kHz crystal connected, it will be used as the source for the low frequency clock. Otherwise the internal 32 kHz RC oscillator will be used. The low frequency clock is used by the delay(ms) and millis() Arduino API's.

The Generic nRF51 and nRF52 board options have an additional menu item under Tools -> Low Frequency Clock that allows you to select the low frequency clock source.

This core is based on the Arduino SAMD Core and licensed under the same GPL License

The following tools are used:

• GCC ARM Embedded as the compiler
• A forked version of OpenOCD to flash sketches