Comments (9)
Well, after install v 0.87, no way to choose port.
KE0DDV: There is not G108 option in this version.
Finally removed app, installed previous version without success, but then installed again v 0.87 and achieved all running doing this:
- Install app
- Turn on X6100
- Connect USB cable to X6100
- Connect phone with provided usb-C cable and OTG adaptor
- On the phone screen appeared 2 port choices, selected the 2nd one.
- App started decoding, cat running but little power out. Just turn up the phone audio level and that was all!
Thanks to all giving support here!
from ft8cn.
Try selecting G108 Xiegu radio. When you plug in the usb cable to android device watch for opportunity to select usb port. On my rig, if I choose the higher numbered one I get cat control, waterfall and decoding. However, when transmitting although red light on the 6100 comes on, 0 power out and ALC of 100. On a Facebook forum two others had same problem, and a third said this is a known issue. I've considered reverting to a previous version of the app, although I have no reason to believe this will help except that one of the hams with the same problem said it had come on suddenly not too long ago--maybe the result of and update?
from ft8cn.
Might help might not. Had same issue on my 991 then I changed microphone input in settings to rear and then it worked in usb not usbdata
from ft8cn.
@EA2CW Thanks. I didn't expect a phone volume level to be related a power of the x6100 + U-DIG.
from ft8cn.
I have a similar issue where there is no audio at all but the CAT is working fine... tried factory rest as well as using X6100 G90 and ICOM7100, still the same...
from ft8cn.
Thanks for the suggestions above. Unfortunately my problem remains the same as you described in the first post.
Comm via USBC/OTG works fine, traffic is being decoded, and displayed properly but there is no rig control thus no TX at all.
Tried changing the serial port to the first one than back to the second one, droppin the port speed to 9600 Baud and even the radio model (running a Xiegu X6100) without any success.
Any suggestions?
from ft8cn.
Update. The problem seems to be related to my ASUS Zenpad tablet. The same software version works fine when running on my Android phone. Next step is updating the firmware on the ASUS Zenpad and see if that helps.
from ft8cn.
I had the same issues with V.0.88 und V.0.87: Decoding ok but no TX. TRX showed just 0W power and ALC 100.
Then I've tried out V.0.86. I had to delete all app settings and configure it again. There was only one version of the X6100 to chose (instead of two like with the newer version). And that worked fine: Both TX and RX are working for me. I had then just to fine tune the signal level of the app and volume settings of the phone for better ALC.
from ft8cn.
Thanks for the suggestions above. Unfortunately my problem remains the same as you described in the first post. Comm via USBC/OTG works fine, traffic is being decoded, and displayed properly but there is no rig control thus no TX at all. Tried changing the serial port to the first one than back to the second one, droppin the port speed to 9600 Baud and even the radio model (running a Xiegu X6100) without any success. Any suggestions?
I have the same issue with a REDMI tablet: I changed cable and OTG, now I have the Serial connection question (and chosing first or second is the same), I can receive but cannot control the rig nor transmit. To be able to control the rig, I must keep the cable connected, connect the X6100 and the tablet through Bluetooth and switch control to Bluetooth, set the tablet volume to MAX and (between some X6100 crashes) I can now transmit. Only v.0.88 works.
I have tried to setup my Samsung Galaxy A52 both with 0.86 and 0.88 but none works (cable, Bluetooth, nothing)
from ft8cn.
Related Issues (20)
- Feature request: Allow transmission to start part-way through a cycle
- Ft8cn locks up with yaesu ft-710
- Insufficient audio HOT 1
- Using FT8CN for Field Day? HOT 1
- Unconfirmed QSOs
- 请问作者能不能在cat选项下面的网络IP输入中新增域名输入 HOT 3
- Yaesu FT-991A USB / DATA-USB incorrect mode settings HOT 2
- Yaesu FT-991A incorrect mode selected / RTTY-USB Selected HOT 9
- v.0.91 No TX audio with X6100 firmware 1.1.7.2 (September 2023) HOT 16
- Serial Port error/no transmit with trusdx HOT 10
- 【求助】ft8_lib中kiss_fftr快速傅里叶变换后如何得到码元? HOT 2
- Transformation of callsign HOT 1
- FT8CN cannot decode contest messages HOT 6
- ft8cn create distorted TX signal when using DF upper than 2000Hz HOT 2
- 输出音量的问题 HOT 2
- KX3 Setup HOT 2
- Free text limitation HOT 2
- Not working "Save QSO for SWL" function HOT 1
- Feature request: Add method to change port number of the WEB UI HOT 2
- another wrong QSO case HOT 2
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ft8cn.