printersforants / salad_fork Goto Github PK

Does it make any notable difference if I use Nema 14 35STH52 rather than the Nema 14 35STH48 for the A/B Motors?

The 35STH52 has 0.37 N/cm of Holding Torque and the 35STH48 has 0.40 N/cm Holding Torque. Does the 0.03 N/cm difference make a difference?

The cowling was probably taken from pre-release version and is symmetrical (has fillets on both left and right) and tool mounts from v0.2 are asymmetrical, with the chamfer on one side only.

Not a huge complaint, however the right z motor mount plate is missing the salad fork logo. I am wondering if I can just mirror the left to get the logo on both?

the underside of the bed z carriage is missing where the bearing is mounted to the bed

All the document links in "https://github.com/PrintersForAnts/Salad_Fork/tree/master/docs" are broken.

https://github.com/PrintersForAnts/Salad_Fork/blob/master/STL/Frame/z_chain_mount_x1.stl
is a 3 hole mount and the rear Z is a 2 hole igus mount

would be nice if they matched so i didnt have to shrink a trident one down :D

While I appreciate the new extensive manual, unfortunately due to my eyesight, I cannot read anything that isn't in Dark Mode. This is why I loved the web manual you had for v1.0 and why I opened the issue about the 404 error with the Docs.

I never liked Dark Mode until I got cataracts, now I can't see anything unless it's in Dark Mode.

Are there any differences between the v1.0 and v1.1 parts that would stop the v1.0 panels from working with the v1.1 printed parts?

Just want to verify before I waste my time printing the new v1.1 parts.

Also are there any printed parts that are identical to their v1.0 versions so I don't reprint them?

You are missing the picture in xy_motion.md for the Motor A pulley mount orientation. You have it for Motor B but not motor A.

The image exists in the image folder of the docs but is not displayed in the actual xy_motion.md file.

https://github.com/PrintersForAnts/Salad_Fork/blob/master/docs/images/a_drive_pulley_detail.png

Is it possible to add allen wrench access holes on A_Drive_Frame_Lower_x1.stl for the y_endstop m2x10 screws used on A_Drive_Frame_Upper_x1.stl? I decided to use sensorless homing and wanted to remove the endstop. I had a heck of a time removing the screws after the mount was fully assembled and belted. Thanks in advance either way!

Hey, thanks so much for this project and putting the manual together! I'm looking forward to rebuilding with 1.1.

Anyway, while perusing through I noticed the table of contents isn't always correct. Here's what I've found that I think should be updated.

• Klicky Assembly says 122 when it should be 121. The link is correct.
• Carriage and Belts says 132 and the link goes to 131, when they should be 130.
• Toolhead says 143 and the link goes to 157, when they should be 142.
• Skirts says 169 when it should be 168. The link is correct.
• Electronics says 186 when it should be 185. The link is correct.
• Panels says 210 when it should be 209. The link is correct.

Thanks again! 🎉

The Docs for Klicky (https://github.com/PrintersForAnts/Salad_Fork/blob/master/docs/klicky.md), says align the tab with the top of the A mount, but the tab is on the top of B mount in the STLs (https://github.com/PrintersForAnts/Salad_Fork/blob/master/STL/Motion/B_Drive_Frame_Upper_x1.stl).

Would it work to do dueling zero on a salad fork to make it idex

For accented parts you should put [a] or mention when a part is an accented part when calling out printed parts in the manual.

I spent way too much time looking in my printed parts for the A and B tensioners in my primary color parts bin only to double check my printer logs to make sure I did print them only to see that they were accented parts.

Would make things a lot easier.

Even with feet added heatsinks protrude from base of printer so much that you cannot use heatsinks.

This is true for M5P mount and Octopus mount I have not tested spider mount yet

The BOM says I need 2 GT-2 20T 6mm Pulleys (5mm bore) but the documentation for the XY motion says it's 16T pulleys. Which is it supposed to be?

Since there is no SaladFork Cowling for a Revo Voron Hotend, i made A remix. Please add it to Toolheads
SaladFork_Revo_Cowling.stl.zip