ramalama2 / voron-2-mods Goto Github PK
View Code? Open in Web Editor NEWAll my mods at one place
License: GNU General Public License v3.0
All my mods at one place
License: GNU General Public License v3.0
Hi Rama,
Thank you for the amazing work you guys have been doing with this.
Are there any plans to make the same modifications to the ERCF version of the LGX Lite model from Eytecz?
Alternatively, are you able to describe the relevant changes you've made?
That way I can try to repeat them myself on the ERCF version from Eytecz's models.
Thanks, Jaans.
PS: I know there is an ERCF branch with StallGuard to provide an option to not need the toolhead filament sensor, but that doesn't suit me.
Ive printed a few of these now and always manage to break off the top locator pins at the unsecured end. Would be helpful if you could revise these to make them a little more robust
Sorry to bring this up as an issue, but I wasn't sure where else to contact you. Can the stock chain anchor be used with the SB_LGXlitePCB? I have a 3 hole cable chain.
Is there any way to modify this design to suit distances from bed to chain all the way down to 72.5mm?
Doing a new 2.4r2 build. Some observations: Printed really well - followed instructions on Github re assembly - no issues at all. When installing the idlers on Y on a new build, following the manual, it may be confusing for newbies as the original idlers have 2 x 5mm holes on the top and a 5mm and 3 mm on the bottom, which allows for easy orientation (as per the manual). This mod has a 5mm and 3mm on both top and bottom and pully orientation may be tricky. As it is still in Beta, this may be something to consider.
I am looking at the Macro for Decontaminator Purge Bucket & Nozzle Scrubber. I have my brush at rear (y) and center (x). Not sure in marco how I change scrub location.
Not really an issue just an FYI.
MacMaster-Carr carries 5M 22mm 18-8 Stainless Steel Button Head Hex Drive Screws for $11.00 pack of 100.
Can be found at this link.
Also, M5 washers DIN 433 18-8 Stainless Steel from MacMaster-Carr at link for $3.71 pack of 100.
Also, I have used your latest STEP files (awesome! Thank You!) and assembled them in Fusion360. I have put some samples:
Pic1
Pic2
Pic3
Late me know if you would like some larger or you can use these.
Cheers!
Hi, great mod! Thanks! Are these compatible with MGN9 extrusion backers?
Hello
Thanks for your Voron 2 mods
You can also make your Cura profile for ABS available via Github
It's hard to find on the web
greet
Martin
The Pins for the fantoolboard doesn't fit. It is not as close to the edge as you designed it.
Could you please upgrade this?
if you could make a multi body idler covers so that the logo can be printed a different color that would be amazing. Multi body has really become mainstream since the release of V0.2. The 0.2 skirts have mulit body in the Voron official git
I have wago 221 mounts I brought recently. Their widths 15.75mm wide. The bedpan's wago width is 12.6 mm. There appears to be enough space to fit 6 wider wago mounts
This isn’t an issue, just wanted to say Option_without_LGXlite-FanPCB front cover works like a charm. Thanks so much!
Thank you for mention. Will test your version btw. I already added version that fits both e3d and dragon but it's little less stiffer than the original one. (i think your version will fit to e3d too)
On my Voron 2.4 - 300, the measurement between my bed and chain is 74.13mm, so ideally a bucket size of 73.5 would work. Unfortunately the buckets in the STL folder don't go this small in size. Would it be possible to create some smaller sized buckets please?
F360 is not importing the files without giving a translation error pointing towards the file being corrupt/incorrectly formatted. Anyway to upload the files as either .step or .f3d ?
This is kind of a nitpick more than anything since the belt is securely held either way.
Take the upper left belt clamp for instance. Assuming that the small hole goes in the back, and the groove for the belt is at the bottom, there is a cutout on the left side. I think this cutout should be on the right to give the belt space to drop in and route to the groove at the bottom.
Feedback on the cable cover test1. It fits perfectly without the probe, FS, main 14-pin plug, or led plugs connected into the board, however with those connectors plugged in the cable cover won't close. It printed fine and doesn't seem too thin.
Thanks for the great projects Ramalama2! Lovin' your work!
When using the mounting system from this repo on my main hotend PCB, the pins on the back of the board shorted against the metal housing of the motor. I was lucky that the PSU overcurrent protection tripped and nothing was damaged.
I would recommend noting on the instructions that it may be a good idea to trim all pins from the main hotend board flush (or at least the ones for the main plug near the motor housing) and that it may be a good idea to add some insulation between the PCB and the motor for additional safety. I just covered pins on the back of my board with a couple of layers of kapton tape after trimming the pins flush.
Thank you for the LGX lite mod!!
I'm looking at this image from it and I'm somewhat confused:
https://github.com/Ramalama2/Voron-2-Mods/blob/main/SB_LGXlitePCB/Images/3.jpg
Is the text meant to be swapped with the other image? Did you not mean that your new PCB is the better solution?
Or am I completely misunderstanding something here?
Thanks for your time and sharing this mod
Dear Rama,
for CAD would it be possible please to avoid .ipt files.
Those extensions dropped out of Fusion 360 non commercial license; that restricts a lot their usability from others.
Many thanks
Are the left and right portions of these:
going to work with the default inlets:
the description says to simply print things 2x, but the GE5Cs mention a left and right. why is that?
just want to make sure i have what i need before install.
thanks!
please add the trident version with the nipple fix change =) thanks
The filename of the Front-Idlers_Z-Belt-Clamp-Upper-Left_x2
and Front-Idlers_Z-Belt-Clamp-Upper-Right_x2
suggest that 2 of each should be printed, but then the instructions only seem to mention 2 of the modified clamps are required (1 each of left and right).
A declarative, efficient, and flexible JavaScript library for building user interfaces.
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google ❤️ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.