WARNING - WORK IN PROGRESS

This code is known to be high risk , but also early-adopter friendly.  

We will remove this warning from the repository when it is no longer required.

firmware for Artoo, the Solo controller

• ARM GCC Embedded - toolchain to build firmware. https://launchpad.net/gcc-arm-embedded
• tup - build tool. http://gittup.org/tup/ (install via homebrew on OS X)
  • fuse-dev is required as a prerequisite to set up tup on Ubuntu (install via apt-get install libfuse-dev)
• pillow - image manipulation in tools/image-codegen.py. http://python-pillow.github.io (install via pip install pillow or similar for your env)
  • note - you'll also need libfreetype installed before installing pillow. (brew install freetype on OS X)
  • on at least one Ubuntu 14.04 image, apt-get install python-pillow was required, rather than pip install pillow
  • on at least one other Ubuntu 14.04 image, `pip install --upgrade pillow' was required, to force getting pillow 2.7.0 rather than using Ubuntu's 2.3.0
• pymavlink - only required when running tools/slip-mavlink.py. http://qgroundcontrol.org/mavlink/pymavlink (install via pip install pymavlink or similar for your env)

To build with tup, simply invoke it at the root of the project directory:

$ tup

cd OpenSolo/artoo vagrant up vagrant ssh cd /vagrant tup

I'm primarily using Qt Creator (https://qt-project.org/downloads) for editing, which is tracked in the following project files: artoo.{config, creator, files, includes}

Any editor you like should be fine, though.

I've been using a Black Magic Probe for debug, the easiest way to setup is to copy the sample gdbinit file:

cp gdbinit.sample .gdbinit

Start a debug session:

$ arm-none-eabi-gdb artoo.elf
$ ... GDB startup ...
$ (gdb) load
$ (gdb) run

If you get super hosed, you may need to execute mon connect_srst enable, possibly with the reset button held, in order to recover.

Stick calibration data (along with other params) are stored in the STM32's MCU flash. There exists as GUI to calibrate them as part of the manufacturing process, but if you're interested in calibrating an existing Artoo, use tools/stick-cal.py as follows:

• copy both tools/slip.py and tools/stick-cal.py to the iMX6 board in your Artoo unit, via scp or similar
• ssh into the iMX6, and run python stick-cal.py, move the sticks and camera controls to their extremes, then press ctrl-C to complete the calibration

It is possible to do some basic testing against a simulated vehicle with the SITL environment provided by ardupilot. http://dev.ardupilot.com/wiki/setting-up-sitl-on-linux should get you set up to run it.

To connect your board to the simulation environment:

• connect an FTDI cable (or similar) to the UART that is normally connected to the iMX6
• if using a VM, pass the virtual serial device into the VM
• run tools/slip-mavlink.py (within the VM if you're using one) - this translates mavlink data from SITL into SLIP encoded data, and passes it to the STM32. It should print the IP address it's listening on - pass this to the --out argument of SITL when you start it below.

From within the ardupilot project folder, start up SITL and then :

$ cd ArduCopter
$ ../Tools/autotest/sim_vehicle.sh --console --out xxx.xxx.xxx.xxx
$ ... SITL starts up ...

Now, stick values and mavlink data are sent bidirectionally between artoo<->SITL, and you should be able to fly as normal.

For print/log-based debugging, semihosting support is available (i've only tested this with Black Magic Probe, though hopefully openocd supports it as well).

In the top level Tupfile, uncomment SEMIHOSTING := yes and rebuild. You can now use the DBG_LOG() macro in the same way that you'd use printf() (it's aliased directly to printf when semihosting is enabled) and you should see the output in your gdb session.

Code should not be checked in with semihosting enabled, since we don't want to link against those libraries in a production build.