This is a single expansion board designed for the Tandy 1000 EX and HX computers, to include the following upgrades:

• 640KB Base System Memory
• 96KB Upper Memory
• 16550-based DE9 Serial RS232 Port
• XT-IDE based CompactFlash "Hard Drive"

This board is for the Tandy 1000EX and 1000HX computers only. It will not work in any other computer model as it is. You must remove any expansion cards already in the computer, this is designed to be a single-board upgrade and has no provisions to allow for any other expansion cards.

This board plugs into the Tandy PLUS interface, and takes up "Slot 2" on the rear of the computer. Please be careful to align the PLUS bus connector before pushing down, to avoid bending pins on the computer. Secure the backplate to the computer with two screws. The IDE BIOS will automatically start and boot directly to the CF card on 1000EX machines. 1000HX loads a boot menu by default, and you will need to press F4 to load the IDE BIOS. If you want to bypass the Tandy DOS ROM and boot menu, run "SETUPHX" and change the "Primary Start-up Device" to "DISK" and press F1 to save.

This board has no configuration jumpers and is designed to be plug-and-play. The only jumper is to enable programming the ROM. Install the jumper to flash the XT-IDE BIOS, otherwise the jumper should be removed. All assembled boards and kits sold by me come with a pre-programmed ROM, and this jumper should be left empty.

The board is hardwired with these memory locations/ports:

SRAM:  0x0000-0x5FFF, 0xC800-0xDFFF
UART:  0x3F8, IRQ 4
IDE:   0x300
ROM:   0xC000-0xC7FF

All functions of the board are independent, no parts are shared between functions. If you do not want to use a specific function, you can safely omit any parts referenced with the function in the name (such as "232" for RS232).

Recommended assembly order: (Shortest to tallest)

• 1 - Resistors (R1-R3, R4 for v1.8+)
• 2 - Bypass Capacitors (C1-C16, only noted as "0.1uF" on the boards)
• 3 - 74 series Chips (U1-4, U6-7, U9, U11-13)
• 4 - ROM Socket (U5 Socket)
• 5 - SRAM Chip (U10)
• 6 - Oscillator (OSC1)
• 7 - UART Socket (U8 Socket) - Pay very special attention to the orientation! See note below.
• 8 - Connectors (BUS1, CF-J1, CF-J2, 232-P2)
• 9 - ROM and UART chips into their sockets.
• 10 - CF Adapter
• 11 - Backplate

NOTE: Please take careful note of part orientation. To optimize some trace routing, not all chips are oriented in the same direction. 232-U6, 232-U8, and RAM-U11 are all opposite oritentation than the other horizontal chips. Installing these backwards will destroy the chips. Pay special attention to 232-U8's socket, it must be installed with the "Pin 1 Arrow" installed facing towards the left of the board. 232-OSC1 is installed "upside down", with the squared corner facing the upper right.

Note: All 74LSxx series logic ICs can be substituted with any family with "LS" or "T" in the name, such as ALS, ACT, AHCT, or HCT among others.

Note2: For the BUS1 Connectors, I have many of these left over from my last order of custom connectors. You can buy them from me for $1/ea plus shipping. Even for one, it is far cheaper than the $13 that Mouser wants.
For small quantities (1-20 connectors), visit my Tindie store to order: https://www.tindie.com/products/rkrenicki/tandy-1000-ex-and-hx-bus-connector/ For larger quantities, please email [email protected].

This board uses the XT-IDE Universal BIOS. I have included pre-configured images for 2.0.0B3 r602 (latest version as of the time of writing this). The 3in1BIOS-8088.zip will work on any EX or HX computer, and is the version that I preload on assembled boards and kits. I have also included a V20 Enhanced version for any EX/HX that has an NEC V20 (or clone) installed. This enhanced version will roughly double your disk speed, but only works on V20 machines.

This board is designed a specific version of a CF-IDE adapter. They are widely available on eBay and AliExpress. It bears the mark of "IDE to CF Ver.D2". It can generally be identified by the metal cover over the CF card connector. I do not have a link to any one specific vendor or listing, but if the adapter includes the metal backplate and has a metal cover over the CF slot, then it should be correct.

The CF adapter does also need a few modifications, please refer to "PDFs\IDE Adapter Modifications.pdf" for details. It also has photos of the adapter for reference to buy the proper adapter. The backplate also has provisions for a mounting tab, please follow the directions found in "PDFs\Backplate Directions.pdf"

If you have any questions, feel free to join the Discord server below and ask in the #tandy-3in1-support channel.

I have started a Discord server for more real-time technical support, as well as discussion for my various projects in progress. You can follow this link to join: https://discord.gg/QmFssyXnQt

• KiCAD EDA

• Rob Krenicki - rkrenicki

This project is licensed under the Creative Commons - Attribution - ShareAlike 3.0 License

This board was derrived from works by, uses design elements from, or contains sofware writen by the following:

• Sergey Kiselev (http://www.malinov.com/Home/sergeys-projects)
• James Pearce (https://www.lo-tech.co.uk/)
• Adrian Black (https://www.youtube.com/user/craig1black/featured)
• Jacob Dorne of Monotech PCs (https://monotech.fwscart.com/)
• XTIDE Universal BIOS Team (http://www.xtideuniversalbios.org/)