Helpful notes
tube ø indre 105 ø ydre 110
Power input 12 V
Calculations:
- LED current is approximately equal to: 0.5 / R3
- R3 power: the power dissipated by the resistor is approximately: 0.25 / R3. choose a resistor value at least 2x the power calculated so the resistor does not get burning hot.
so for 700mA LED current: R3 = 0.5 / 0.7 = 0.71 ohms. closest standard resistor is 0.75 ohms. R3 power = 0.25 / 0.71 = 0.35 watts. we'll need at least a 1/2 watt rated resistor.
Brand new and high quality. High brightness, light and color consistency. Color: Red, Green, Blue. Viewing Angle: 140 degree. Wavelength: R:620-630nm G:515-525nm B:460-470nm. Voltage(Vf): R:2.0-2.5V G:3.2-3.6V B:3.2-3.86. Luminous intensity: R:30-35lm G:40-45lm B:15-20lm. Current: each 350mA
Wo for 350mA LED current: R3 = 0.5 / 0.35 = 1.42857142857 ohms. closest standard resistor is 1.5 ohms. R3 power = 0.25 / 1.42857142857 = 0.175 watts. We use two 3.3 Ohm resistors
3 in parralell calculation We have 350 mA LEDS x3 = 1050
R3 = 0.5/1.05 = 0.47619047619 R3 power = 0.25 / 0.47619047619 = 0.525 W
Standard resistors are 1/4W so 2 of them si okish In parralllel the closest we get to 0.47619047619 ohm with two standard resistors is with two 1 ohm resistors
pcb2gcode --back /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_copperBottom.gbl --drill /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_drill.txt --outline /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_contour.gm1 --zwork -0.2 --zsafe 25.0 --mill-feed 6 --mill-speed 30000 --metric --offset 2.0 --basename johandrill --zdrill -2.0 --zchange 10.0 --drill-feed 6 --drill-speed 20000 --cutter-diameter 3.0 --zcut -2.0 -cut-speed 20000
pcb2gcode --back /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_copperBottom.gbl --drill /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_drill.txt --outline /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_contour.gm1 --zwork -0.2 --zsafe 25.0 --mill-feed 6 --mill-speed 30000 --metric --offset 50 --basename johandrill --zdrill -2.0 --zchange 10.0 --drill-feed 6 --drill-speed 20000 --cutter-diameter 3.0 --zcut -2.0 --cut-speed 20000 --milldrill --fill-outline --outline-width 2
--fill-outline --outline-width 2 for using fritzing outline file
http://simplegcoder.com/js_editor/
http://simplegcoder.com/js_editor_framework/
http://fablabamersfoort.nl/drill2gcode/
pcb2gcode --back /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_copperBottom.gbl --drill /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_drill.txt --outline /home/parallels/Desktop/psf/TheTree/3leds/series/inseries_contour.gm1 --zwork -0.008 --zsafe 1 --mill-feed 6 --mill-speed 30000 --offset 1 --basename __newdrill --zdrill -0.07 --zchange 0.4 --drill-feed 6 --drill-speed 20000 --cutter-diameter 0.015 --zcut -0.07 --cut-speed 20000 --fill-outline --outline-width 0.01
Remember to connect MAX485 pin to ground with jumper
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent