Comments (9)
Update:
The first problem concerning low voltage has been more or less resolved. When I measured 1.7 volts it was with the LED and a 220R resistor attached. Without the LED I got 2.45 volts, so I simply used a smaller resistor than what I would usually use. Meanwhile, I solved the problem with the relay by using a MOFSET between the PCF8547 port and the module's trigger pin.
The second issue unfortunately hasn't been resolved yet. The PCF8547 ports are on at startup while the GUI indicates that it's off, so I still need to turn the port on and off at the beginning. I probably can write a rule to do this, but I don't like the idea of having the relays and LEDs quickly switch on and then off when starting or rebooting the device.
from sonoff-tasmota.
I will try on the weekend to reproduce this. I do not see the issue with the release I loaded into my watering equipment
from sonoff-tasmota.
Thanks. By the way, here is the workaround I am currently using. It's a rule which switches all ports on and then off again:
on Power1#Boot do backlog power0 on; RuleTimer1 1 endon on Rules#Timer=1 do power0 off endon
When the system starts the ports are on for about three seconds and then switch off. The web GUI is also subsequently synced as a result.
Since I will be using the PCF8574 on a board with 4 relays connected to lights which can be turned on not only by WiFi but also RF433 as well as a manual switch, it's not that bad because hopefully it doesn't have to be powered on or reset often. Still, when it does (such as in the case of a power failure) it's nevertheless a little strange to have all four sets of lights turn on for a few seconds at the beginning.
from sonoff-tasmota.
if i make all 8 as output..its working fine with relay. but one problem i am facing is if all the 8 relays are on.. while restarting none of the relay is in onstate. but in web interface it show all are on. if i off one relay all are getting on except the one which is off
from sonoff-tasmota.
Ok, this looks like the current state is not send on the init process. I will fix this in the master tasmota and propagate here. Please change to the original tasmota, if possible because nearly all features are now in the main project
from sonoff-tasmota.
what i have to do now.. what means original tasmota.. if seven relays are on. if i restart no issue all are syns well. if all 8 relays are on..on restart problem arises.. none of the relay will get on. in web interface all the relays will be in on state. if i tried changing any one to off in web ui..it will on the remaining seven relays.
from sonoff-tasmota.
i compiled from development version
Program Version | 8.1.0.4(tasmota) |
---|---|
2020-01-23T00:49:07 | |
2_6_1/2.2.2-dev(38a443e) |
from sonoff-tasmota.
This issue has been automatically marked as stale because it hasn't any activity in last few weeks. It will be closed if no further activity occurs. Thank you for your contributions.
from sonoff-tasmota.
This issue was automatically closed because of being stale. Feel free to open a new one if you still experience this problem.
from sonoff-tasmota.
Related Issues (20)
- SetOption80 1 HangUp the Device HOT 13
- Can´t connect to WIFI after upload your Firmware HOT 2
- SHUTTER50PERCENT not work HOT 7
- Erratic Behaviour when Slow Blinds - includes fix HOT 1
- Dim the lights in the switch? HOT 6
- Shutter dead time support HOT 11
- Vcc in state HOT 3
- Alexa Dimming doesnt work HOT 4
- PCF8574 on master HOT 2
- MQTT Report during movement HOT 1
- DeepSleep consumption HOT 1
- MQT: TLS connection error: 0 HOT 4
- Calibration 2nd shutter HOT 1
- Shutter with LC-TECH X2 in mode 1 allows changing direction without power removal HOT 5
- MQT: TLS connection error: 0 HOT 1
- Mq sensor
- Sonoff touch TX T3 Us
- upgrading from Sonoff-Tasmota 6.5.0.11 stb-1.5 by Theo Arends HOT 7
- Shutter - inverse mode - slider not correct HOT 5
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from sonoff-tasmota.