The following document outlines the design, implementation and real-time dependecies of a music synthesizer for the 2nd coursework of the Embedded Systems module.

The sytem at hand executes several real-time tasks, including:

• Scannng the key matrix
• CAN decoding task
• Updating the display
• Generating sound
• Receiving CAN Messages

Function: void scanKeysTask(void *pvParameters)

Purpose:

• Decode the key matrix, obtaining the states of the keys, knobs and joystick
• Obtain the most recently changed note from the decoded key matrix
• Select the appopriate step size for the most recently changed note
• Transmit the most recently changed note, alongside its state (pressed or released) and octave using CAN
• Obtain any changes in the knobs from the decoded key matrix, corresponding to octave, waveform, send/receive mode or volume

Implementation: Thread

Minimum initiation time: 20ms

Maximum execution time: 0.74ms

CPU Resource Usage: 3.68%

Priority: Highest, as obtaining the note, volume and octave is required for playing the sound, transmitting over CAN and displaying on the screen. All other tasks depend on the results obtained from scanning the key matrix.

Function: void decodeTask(void *pvParameters)

Purpose:

• Decode the incoming CAN message in the Receive Queue: msgInQ
• Determine if message is key pressed, key released or the announcement of the main synthesizer to put other modules into SEND mode.
• Update the array of currently active notes
• Set the current step size, with respect to the most recently active note.

Implementation: Thread

Minimum initiation time: The input for decodeTask() is a Queue, filled from within CAN_RX_ISR(). The resulting minimum initiation time is the size of the queue multiplied by the minimum initiation time of the function that fills the Queue. In this case: 0.7 * 36 = 25.2ms

Maximum execution time: 0.76us

CPU Resource Usage: 0.00304%

Priority: Medium, due to a lower initiation time, compared to scanning the key matrix. Furthermore, in order to receive CAN messages, they had to be transmitted first - which is handled in scanKeyTask.

Function: displayUpdateTask(void *pvParameters)

Purpose:

• Display the currently selected note (string)
• Display the current volume level (int) or an animated icon (XMB icon)
• Display the current octave (int)
• Display the current waveform (XMB icons), including sawtooth, triangle, sine and square

Implementation: Thread, executing every 100ms.

Minimum initiation time: 100ms. While a refresh rate of 10Hz sounds insufficient (compared to modern monitors); the display is largely static. Therefore, 100ms is a perfectly accetable design choice, without any noticeable delays.

Maximum execution time: 17.01ms

CPU Resource Usage: 17.01%

Priority: Lowest, there is no point in updating the display if the current note, volume or octave have not been updated - all of which take place in the scanning key matrix task.

Function: sampleISR()

Purpose:

• Adds the sample step to the accumulated value, corresponding to the desired frequency
• Sets the output voltage, by using the accumlated value and the desired volume
• Writes to analogue output, generating the desired sound

Implementation: Interrupt, executing with a frequency of 22kHz. An interrupt is chosen as responding quickly is needed for playing sound. Otherwise, delays between the key press and the sound would exist.

Minimum initiation time: 45.5ms

Maximum execution time: 12.17us

CPU Resource Usage: 0.27%

Function: CAN_RX_ISR()

Purpose:

• Copies incoming CAN messages in the CAN buffer to an internal - larger - buffer, to be handled later by decodeTask()

Implementation: Interrupt, executing whenever a new CAN message is received. An interrupt is chosen as the receive buffer is small and needs to be emptied often to avoid loss of CAN messages.

Minimum initiation time: No set minimum initiation time, runs as often as needed. Frequency limit of this interrupt is determined by the maximum execution time and the time duration of CAN Messages, which is 0.7ms

Maximum execution time: Requires a CAN Message to be received from another board, which would need to flood the CAN bus. Maximum execution time of one iteration is likely below the length of a CAN message and not easily quantifiable.

CPU Resource Usage: Not quantifiable as the execution time could not be measured.

From the minimum initiation and maximum execution times obtained in the last section, the critical analysis is calculated using the formula provided in the lecture notes. The lowest priority task is updating the display. The minimum initiation and maximum execution time are summarised below, in ascending order:

1. CAN_RX_ISR - Not quantified & 0.7ms
2. scanKeysTask - 73.65us & 20ms
3. decodeTask - 0.76us & 25ms
4. sampleISR - 12.17us & 45.15ms
5. updateDisplayTask - 17.07ms & 100ms

Therefore, total latency is slightly over 23.07ms. The exact latency could not be calculated, as the exact worst case execution time of CAN_RX_ISR is not known. However, as the specified latency is less than 100ms, the schedule will work.

The total CPU usage is calculated by dividing the total latency by the highest initiation time. In this case the CPU usage is ~25%.

• currentStepSize, safe access guaranteed using std::atomic<uint32_t>, stores the step size of the most recently pressed key, to be used within sampleISR()
• keyArray, each element within the array is of type std::atomic<uint8_t>, stores the current state of the key / encoder matrix
• msgInQ, handled by FreeRTOS, pointer to the next item in the received CAN message queue
• latestKey, guarded by std::atomic<int>, ensures that the current note is maintained as an integer value
• selectedWaveform is an int (std::atomic<uint32_t>) corresponding to the currently selected Waveform type, that determined if the output is a Sawtooth, Square, Triangle or Sine wave.
• octave is modified when the key is changed and the message displayed on the screen needs to be displayed, stored as an int.

It was decided to use C++ std::atomic, as it is easier to use and implement, while providing the same functionality as a mutex. According to the documentation: "Each instantiation and full specialization of the std::atomic template defines an atomic type. If one thread writes to an atomic object while another thread reads from it, the behavior is well-defined (see memory model for details on data races). In addition, accesses to atomic objects may establish inter-thread synchronization and order non-atomic memory accesses as specified by std::memory_order." - CPP Reference "std::atomic"

std::atomic makes use of atomic builtins within GCC in order to prevent data races from occuring when there are simultaneous accesses of a variable from different threads. The result of wrapping our global variables in std::atomic<> is that any access to these variables is always atomic, so data corruption is prevented. In some cases, such as keyArray, the array may be partially updated. This is not an issue for data integrity or program operation, as the keyArray update will simply be slightly delayed. This delay is unlikely to be noticable to the user.

msgInQ is used as a FIFO buffer for CAN messages, to supplement the small buffer of the CAN system and allow for more messages to be retained, increasing the required minimum initiation time.

The below figure displays a graph of the dependencies between the various tasks. It can be clearly seen that the dependancies are not cyclical, therefore there is no capability for a deadlock to occur.

Several advanced features were implemented, including:

• Multiple waveforms
• User-friendly icons
• Automatic sender mode configuration using reciever module
• Finer volume control
• Storing multiple key presses

Our system implements several waveforms - sawtooth, triangle, sine, & square.

• Sawtooth was implemented first, by incrementing the step size and waiting for overflow to occur, resetting the waveform.
• Square is implemented by taking the sign of the sign and appropriately scaling to low or high voltage depending on this.
• Triangle is implemented as a variation of Sawtooth, taking the absolute value of the phase shifting to remove the DC offset and then doubling to restore the original size.
• Sine is implemented by calling to a look-up table, preestablished with the corresponding value of a sine wave at the relevant point in the input waveform

Using XMB icons, the display was made more user-friendly, containing a volume icon, that is animated to the current volume level. Furthermore, by pressing the knob, this icon is toggled to display the volume as an integer. Finally, several icons are used to display the current waveform.

When one of the keyboards is set to be the receiver, the encoder automatically sets the other keyboards to be CAN senders.

A finer volume control method was implemented, allowing the user to set a more accurate volume. The resolution is now set to 20 steps, utilsing some additional algebra.

The original code was modified to store multiple keys as the current key. This was achieved by using an array. Currently, only the most recently pressed key is played - however, given the array, this is easily modified to play more than note.