Climatisation not working about weconnect-cli HOT 15 OPEN

controls for auxiliary heating are in auxiliaryHeating and not climatisation

from weconnect-cli.

You can send start or a number representing minutes.

and you have to add the —spin for the auxiliary heating

from weconnect-cli.

Hi Till,

so the correct command would be
"--username [email protected] --password ................ --spin #### set /vehicles/WVGZZZ5NZLW......./controls/auxiliaryHeating start" correct?

How does the minute argument work?

"--username [email protected] --password ................ --spin #### set /vehicles/WVGZZZ5NZLW......./controls/auxiliaryHeating 10" -> does that mean the heating will go on for 10 minutes and then turn off?

Thank you for your support :-)

from weconnect-cli.

I just tried: "[...] set /vehicles/WVGZZZ5NZLW3...../controls/auxiliaryHeating start"
and got the response: id /vehicles/WVGZZZ5NZLW3...../controls/auxiliaryHeating not found

from weconnect-cli.

also tried "[...]/auxiliaryheating start" but get the same response

from weconnect-cli.

Try to use the list -s command to see what is available.

from weconnect-cli.

Hi Till,

it shows me this list:

/vehicles/WVGZZZ5NZLW....../controls/access
/vehicles/WVGZZZ5NZLW....../controls/climatisation
/vehicles/WVGZZZ5NZLW....../controls/honkAndFlash
/vehicles/WVGZZZ5NZLW....../controls/wakeup
/controls/spin

from weconnect-cli.

Hi Till,

any alternative suggestions I could try?

BR

from weconnect-cli.

I have a suspicion. Can you have a look if the controls appear after you configured a timer for the auxiliary heating?

from weconnect-cli.

Hi Till,

sorry for maybe a stupid question: Do you mean with timer the departure time or how long the heater is supposed to run?
Should I set the timer in the car or using the Volkswagen App?
Or using your utility? If so, how would I do that?

And what to you mean with "if the controls appear"? Where are they supposed to appear?
Does that referred to the "list -s" command?
Sorry 🙈

from weconnect-cli.

No reason to be sorry, my message was cryptic!
I meant setting a departure timer in the car. It should be enough to have an entry, it does normale to be enabled.
Afterwards there is a chance that a new entry for auxiliary heating might appear in the controls section. The reason is: I only add the controls when I believe the car has auxiliary heating. And I detect that by looking for the Timer Section.
If that still does not help I will need to do some changes in the code.

from weconnect-cli.

Hi Till,

thank you for the explanation.
So I set a timer using the volkswagen app for tomorrow morning.
then I did the "list -s" command again and got the following response:

2023-12-06T21:01:30+0100:ERROR:/vehicles/WVGZZZ5NZLW......./domains/vehicleHealthWarnings/warningLights/warningLights/0xA227: warning light icon is not a base64 encoded png
/vehicles/WVGZZZ5NZLW......./controls/access
/vehicles/WVGZZZ5NZLW....../controls/climatisation
/vehicles/WVGZZZ5NZLW....../controls/honkAndFlash
/vehicles/WVGZZZ5NZLW......s/wakeup
/controls/spin

I don't think the warning light has anything to do with it - at least I hope so^^

from weconnect-cli.

Hmmm, ok then I need to rethink my implementation.

from weconnect-cli.

@klucon2 Perhaps it would be better to not post your full VIN?

@tillsteinbach: I just came across this program and decided to try it. Thanks for putting this out there! ❤️

With regards to this issue. I was under the impression turning on climatisation didn't work for me either. I had this issue open in a browser tab because of it. But it turns out I was simply looking at cached results. So I would like to add a positive experience: Climatisation works for me. Car is a ID.3 Business with the ID.Software 2.4 on it.

Command I issued, same as in the opening post:

weconnect-cli set /vehicles/$VIN/controls/climatisation start

So your current implementation does work for some.

from weconnect-cli.

Hi Both,

@stejoo thank you.

@tillsteinbach apparently there are differences depending on the models. Do you think you can look into where the difference lies?

from weconnect-cli.