zhaxia8714 / tayga Goto Github PK
View Code? Open in Web Editor NEWThis project forked from openthread/tayga
License: GNU General Public License v2.0
This project forked from openthread/tayga
License: GNU General Public License v2.0
****************************************************************************** README for TAYGA v0.9.2 ****************************************************************************** Last updated 2010-12-12 -------- Overview -------- TAYGA is an out-of-kernel stateless NAT64 implementation for Linux. It uses the TUN driver to exchange packets with the kernel, which is the same driver used by OpenVPN and QEMU/KVM. TAYGA needs no kernel patches or out-of-tree modules, and it is compatible with all 2.4 and 2.6 kernels. If you're impatient and you know what stateless NAT64 is, you can skip to the Installation & Basic Configuration section. ------------------------------- Stateless versus Stateful NAT64 ------------------------------- Most people are familiar with stateful NAT, which allows N:1 address mapping by tracking TCP and UDP sessions and rewriting port numbers on each packet. Most commonly this is used to translate sessions from multiple "internal" hosts (which are numbered with private IPv4 addresses) onto a single global IPv4 address on the NAT device's "external" interface. Stateless NAT does no such session tracking or port number rewriting. It simply performs a 1:1 substitution of IP addresses using a mapping table provided by the network administrator. For example, an organization whose global address allocation was 198.51.100.0/24 but whose hosts were using addresses in 192.0.2.0/24 could use a stateless NAT to rewrite 192.0.2.1 into 198.51.100.1, 192.0.2.35 into 198.51.100.35, etc, in the outbound direction, and the reverse in the inbound direction. This is commonly done when an organization moves to a new ISP and receives a new IPv4 address delegation of the same size as their old delegation but does not want to renumber their network. TAYGA and other stateless NAT64 translators operate in this fashion. When translating packets between IPv4 and IPv6, the source and destination addresses in the packet headers are substituted using a 1:1 mapping. This means that, in order to exchange packets across the NAT64, each IPv4 host must be represented by a unique IPv6 address, and each IPv6 host must be represented by a unique IPv4 address. How this mapping is performed is discussed in the next sections. In situations where stateful NAT64 is required, TAYGA can be used in combination with a stateful IPv4 NAT such as the iptables MASQUERADE target. This allows the administrator a great deal more flexibility than if stateful NAT were implemented directly in TAYGA. ---------------------- Mapping IPv4 into IPv6 ---------------------- TAYGA maps IPv4 addresses into the IPv6 network according to RFC 6052. This states that a 32-bit IPv4 address should be appended to a designated IPv6 prefix, which we call the NAT64 prefix, and the resulting IPv6 address can be used to contact the IPv4 host through the NAT64. The NAT64 prefix should be assigned out of a site's global IPv6 address allocation. For example, if a site is allocated 2001:db8:1::/48, the prefix 2001:db8:1:ffff::/96 could be set aside for NAT64. (There are several options for the length of the NAT64 prefix, but a /96 is recommended.) The IPv4 host 198.51.100.10 could then be accessed through the NAT64 using the address 2001:db8:1:ffff::c633:640a. Conveniently, it is possible to use the syntax 2001:db8:1:ffff::198.51.100.10 instead. RFC 6052 also specifies a Well-Known Prefix 64:ff9b::/96 which can be used for NAT64 service rather than allocating a prefix from the site's IPv6 address block. However, this comes with several restrictions, primarily that hosts with private IPv4 addresses (10.x.x.x, 192.168.x.x, etc) cannot be accessed through the NAT64. See RFC 6052 for more information. If NAT64 service is needed for only a few hosts instead of the entire IPv4 address space, TAYGA can be configured without a NAT64 prefix, and address maps can be assigned on a host-by-host basis. ---------------------- Mapping IPv6 into IPv4 ---------------------- Being a stateless NAT, TAYGA requires that a unique IPv4 address is assigned to every IPv6 host that needs NAT64 service. This assignment can be done statically by the network administrator, or dynamically by TAYGA from a pool of IPv4 addresses designated for this purpose. Static address mapping is desirable for servers or other hosts requiring a well-known address. Statically mapped addresses may be entered into DNS, for example. Dynamic address mapping allows TAYGA to assign IPv4 addresses to IPv6 hosts as they are needed. By default, these assignments are guaranteed to remain usable for up to two hours after the last packet seen, but they are retained for up to two weeks as long as the address pool does not become empty. Assignments are written to disk so they persist through a restart of the TAYGA daemon, allowing existing TCP and UDP sessions to continue uninterrupted. (Of course, TAYGA also supports the addressing architecture described in RFC 6052 in which IPv6 hosts are numbered with "IPv4-translatable IPv6 addresses" carved out of the NAT64 prefix.) ---------------------------------- Installation & Basic Configuration ---------------------------------- TAYGA uses the GNU Automake/Autoconf system, which requires the `configure` script to be run to generate the Makefile prior to building. The --prefix and/or --sysconfdir options can be specified to the configure script to specify the top-level installation path and tayga.conf file directory, respectively. After unpacking the distribution tar.bz2 file, run: # ./configure && make && make install This will install the tayga executable in /usr/local/sbin/tayga and the sample config file in /usr/local/etc/tayga.conf.example. Next, if you would like dynamic maps to be persistent between TAYGA restarts, create a directory to store the dynamic.map file: # mkdir -p /var/db/tayga Now create your site-specific tayga.conf configuration file. The installed tayga.conf.example file can be copied to tayga.conf and modified to suit your site. Here is a sample minimal configuration: tun-device nat64 ipv4-addr 192.168.255.1 prefix 2001:db8:1:ffff::/96 # replace with a prefix from # your site's address range dynamic-pool 192.168.255.0/24 data-dir /var/db/tayga # omit if you do not need persistent # dynamic address maps Before starting the TAYGA daemon, the routing setup on your system will need to be changed to send IPv4 and IPv6 packets to TAYGA. First create the TUN network interface: # tayga --mktun If TAYGA prints any errors, you will need to fix your config file before continuing. Otherwise, the new nat64 interface can be configured and the proper routes can be added to your system: # ip link set nat64 up # ip addr add 2001:db8:1::1 dev nat64 # replace with your router's address # ip addr add 192.168.0.1 dev nat64 # replace with your router's address # ip route add 2001:db8:1:ffff::/96 dev nat64 # from tayga.conf # ip route add 192.168.255.0/24 dev nat64 # from tayga.conf Firewalling your NAT64 prefix from outside access is highly recommended: # ip6tables -A FORWARD -s 2001:db8:1::/48 -d 2001:db8:1:ffff::/96 -j ACCEPT # ip6tables -A FORWARD -d 2001:db8:1:ffff::/96 -j DROP At this point, you may start the tayga process: # tayga Check your system log (/var/log/syslog or /var/log/messages) for status information. If you are having difficulty configuring TAYGA, use the -d option to run the tayga process in the foreground and send all log messages to stdout: # tayga -d
A declarative, efficient, and flexible JavaScript library for building user interfaces.
๐ Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. ๐๐๐
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google โค๏ธ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.