Giter VIP home page Giter VIP logo

pymata4's Introduction

pymata4

Please note that the pymata4 feature set is now frozen and the project has been placed in maintenance mode.

Please consider using Telemetrix instead.

A high performance, Python client for the Arduino Firmata Protocol.

Pymata4 is a Firmata client that, like its asyncio sibling, pymata-express, allows you to control an Arduino using the high-performance FirmataExpress sketch. It uses a conventional Python API for those that do not need or wish to use the asyncio programming paradigm of pymata-express.

A User's Guide is available, containing an annotated API as well as links to working examples.

It supports both an enhanced version of StandardaFirmata 2.5.8, called FirmataExpress, as well as StandardFirmata and StandardFimataWiFi.

  • FirmataExpress adds support for:
    • HC-SR04 Ultrasonic Distance Sensors.
    • DHT Humidity/Temperature Sensors.
    • Stepper Motors.
    • Piezo Tone Generation.
    • Baud rate of 115200

Special Note For FirmataExpress Users:

pymata4 now verifies the version of FirmataExpress in use. You may need to upgrade to the latest version of FirmataExpress using the Arduino IDE Library management tool.

Major features

  • Fully documented intuitive API

  • Python 3.7+ compatible.

  • Set the pin mode and go!

  • Data change events may be associated with a callback function, or each pin can be polled for its last event change.

    • Each data change event is time-stamped and logged.
  • User's Guide, Including Examples.

  • Implements 100% of the StandardFirmata Protocol (StandardFirmata 2.5.8).

  • Advanced auto-detection of Arduino devices (when using FirmataExpress).

Here is an example that monitors data changes on a digital input pin. It demonstrates both callback and polling techniques

import time
import sys
from pymata4 import pymata4

"""
Setup a pin for digital input and monitor its changes
Both polling and callback are being used in this example.
"""

# Setup a pin for analog input and monitor its changes
DIGITAL_PIN = 12  # arduino pin number
POLL_TIME = 5  # number of seconds between polls

# Callback data indices
# Callback data indices
CB_PIN_MODE = 0
CB_PIN = 1
CB_VALUE = 2
CB_TIME = 3


def the_callback(data):
    """
    A callback function to report data changes.
    This will print the pin number, its reported value and
    the date and time when the change occurred

    :param data: [pin, current reported value, pin_mode, timestamp]
    """
    date = time.strftime('%Y-%m-%d %H:%M:%S', time.localtime(data[CB_TIME]))
    print(f'Pin: {data[CB_PIN]} Value: {data[CB_VALUE]} Time Stamp: {date}')


def digital_in(my_board, pin):
    """
     This function establishes the pin as a
     digital input. Any changes on this pin will
     be reported through the call back function.

     :param my_board: a pymata_express instance
     :param pin: Arduino pin number
     """

    # set the pin mode
    my_board.set_pin_mode_digital_input(pin, callback=the_callback)

    while True:
        try:
            # Do a read of the last value reported every 5 seconds and print it
            # digital_read returns A tuple of last value change and the time that it occurred
            value, time_stamp = my_board.digital_read(pin)
            date = time.strftime('%Y-%m-%d %H:%M:%S', time.localtime(time_stamp))
            # value
            print(f'Polling - last value: {value} received on {date} ')
            time.sleep(POLL_TIME)
        except KeyboardInterrupt:
            board.shutdown()
            sys.exit(0)

board = pymata4.Pymata4()

try:
    digital_in(board, DIGITAL_PIN)
except KeyboardInterrupt:
    board.shutdown()
    sys.exit(0)

And here is the console output:

pymata4:  Version 1.00

Copyright (c) 2020 Alan Yorinks All Rights Reserved.

Opening all potential serial ports...
	/dev/ttyACM0

Waiting 4 seconds(arduino_wait) for Arduino devices to reset...

Searching for an Arduino configured with an arduino_instance = 1
Arduino compatible device found and connected to /dev/ttyACM0

Retrieving Arduino Firmware ID...
Arduino Firmware ID: 2.5 FirmataExpress.ino

Retrieving analog map...
Auto-discovery complete. Found 20 Digital Pins and 6 Analog Pins


Polling - last change: 0 change received on 1969-12-31 19:00:00 
Pin: 12 Value: 0 Time Stamp: 2020-03-07 08:52:10
Pin: 12 Value: 1 Time Stamp: 2020-03-07 08:52:12
Polling - last value: 1 received on 2020-03-07 08:52:12 

This project was developed with Pycharm logo

pymata4's People

Contributors

mryslab avatar rbarzic avatar bsilvereagle avatar

Recommend Projects

  • React photo React

    A declarative, efficient, and flexible JavaScript library for building user interfaces.

  • Vue.js photo Vue.js

    ๐Ÿ–– Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.

  • Typescript photo Typescript

    TypeScript is a superset of JavaScript that compiles to clean JavaScript output.

  • TensorFlow photo TensorFlow

    An Open Source Machine Learning Framework for Everyone

  • Django photo Django

    The Web framework for perfectionists with deadlines.

  • D3 photo D3

    Bring data to life with SVG, Canvas and HTML. ๐Ÿ“Š๐Ÿ“ˆ๐ŸŽ‰

Recommend Topics

  • javascript

    JavaScript (JS) is a lightweight interpreted programming language with first-class functions.

  • web

    Some thing interesting about web. New door for the world.

  • server

    A server is a program made to process requests and deliver data to clients.

  • Machine learning

    Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.

  • Game

    Some thing interesting about game, make everyone happy.

Recommend Org

  • Facebook photo Facebook

    We are working to build community through open source technology. NB: members must have two-factor auth.

  • Microsoft photo Microsoft

    Open source projects and samples from Microsoft.

  • Google photo Google

    Google โค๏ธ Open Source for everyone.

  • D3 photo D3

    Data-Driven Documents codes.