yoshito-n-students / bno055_usb_stick Goto Github PK
View Code? Open in Web Editor NEWA ROS driver of Bosch BNO055 USB Stick
License: MIT License
A ROS driver of Bosch BNO055 USB Stick
License: MIT License
Just a question, does the driver output according to REP-103? Specifically, does the linear acceleration conform to ENU, east-north-up?
I don't know whether the data from the stick is REP-103 formatted, but maybe the driver converts it to REP-103.
This looks like a great ROS package however I don't have a bno055 USB stick yet (in the mail) but I do have the adafruit bno055 board connected via a serial cable. Does the this ROS package work with the adafruit bno055?
I think the adafruit bno055 and the bno055 stick use the same serial protocol so I'm not sure why this isn't working. I'm getting the error "handleWaitResponse: End of file" whenever I try launching a bno055_usb_stick_node. The error prints off about every second.
I am currently using the ROS package rr_bosch_bno055_imu to get data from the adafruit bno055 board and it works fine however it doesn't give access to all the data from the bno055 and it looks cumbersome to modify so that's why I'm hoping this one can work.
Any info would be greatly appreciated.
I'm running ROS kinetic on ubuntu 16.04.
Hi,
I got my BNO055 USB stick from Digikey today (https://www.digikey.com/product-detail/en/bosch-sensortec/BNO055-USB-STICK/828-1045-ND/6136288). But when I plug it in I didn't see /dev/ttyACM0 showing up. So I was wondering if you are using the same hardware (Red PCB) or the green PCB version.
Thanks in advance.
I am trying to add calibration to the software, but I can't find any protocol spec for the USB stick. How did you find out the protocol?
Would be nice to see run directions in the readme.
I used: rosrun bno055_usb_stick bno055_usb_stick_node
but got back error message
[ERROR] [1527981048.145777140]: handleWaitResponse: End of file
I have updated the firmware to the latest: BNO_Firmware_0.3.2.0.hex
. I also updated the controller firmware to BNOinUSBStick_V1.4.fwu3
.
The stick works fine in Development Desktop 2.0.
The stick is at port ttyACM0
.
Thanks for sharing this code. I was trying to connect bno055 with ROS indigo ubuntu 14.04LTS and got the error Incorrect Bosh IMU device response
. I found that while reading from dev the byte array length is zero. Can you tell me how to resolve this error? I'm using bno055 with red pcb.
I'm seeing what appears to be a scale error in the conversion of the gyro measurements. I am using a bno055 with a high precision RTK GPS on a mobile platform, and I'm seeing a non-negligible difference between the yaw angle estimated from the gyro when turning, and the differential angle from the GPS.
From the testing I was seeing what looked to be about a 1.5% scale error (on yaw rate), and that scale error was identical for different bno055 units, so I suspected that there may be a systematic error in the conversion in the driver. Looking a little closer at the code I saw this:
gyr.z = decodeVal(data[5], data[4], Constants::GYR_DENOM) * M_PI / 180.;
where GYR_DENOM
is 16. This appears to follow the Bosch documentation: https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BNO055-DS000.pdf, but the documentation oddly specifies inconsistent conversion factors: 1 degree / second = 16, but 1 radian / second = 900. As it turns out, converting the degrees / second factor to a radians / second factor results in about 916.7, which is pretty close to the observed error. I haven't read Bosch's documentation in detail, but it's possible the the radians / second conversion is the exact conversion, while the degrees / second conversion is an integer approximation. It might also be the case that neither is exact, and there is some other correct floating point conversion factor. In any case, it appears that the radians / second conversion factor is more correct based on what we've seen with our testing.
I assume that this also affects the orientation measurements, but I haven't looked at those to verify.
Hi,
I have got an BNO055 USB Stick and want to use it with ubuntu 16.04 and ros kinetic.
I installed the package and tried to run the node. But when I run the node I get the following output:
[ERROR] [1526481970.305344177]: start: open: Permission denied
I didn't install any other driver or updated the firmware. I just plugged in the usb stick and installed the package. What else do I have to do, when I want to run this node?
Thank you in advance.
Best wishes
anleger
A declarative, efficient, and flexible JavaScript library for building user interfaces.
๐ Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. ๐๐๐
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google โค๏ธ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.