Comments (13)
I have the same problem (not always), firmware Ender3S1-F4-DACAI-T13-LA
115200 baud rate
ɽ���I��F*g��Si��-���cgk�bootloader SD card...
SD����û��update.bin�ļ�
���kC�����)�{�MHYY������N��[)�)i�)++e�N��cy�c��μ
�c��
�o)��k�k{�sik)k����������kk!�!�ki�xzo�o�ު����ػ�������{k�g��ʮ�k[�������ocC�k� ��w�c
���)i���{�H))�ȵa-
250000 baud rate
File opened: XYZCAL2.GCO Size: 645621����f����`��怘start
File selected
����x����x�������������������
Watchdog Reset
Marlin ProUI Version: 2.1.3 MRiscoC
CUSTOM BUILD: 20240201 - 21:38
Author: Miguel Risco-Castillo (MRiscoC)
echo: Free Memory: 53759 PlannerBufferBytes: 1792
echo:A90 stored settings retrieved (827 bytes; crc 52775)
//action:notification Stored settings retrieved
//action:prompt_end
BL24CXX Check succeeded!
echo:SD card ok
echo: Serial 0 baud rate set to 250000
ok P15 B16
from ender3v2s1.
Thanks for the report, how many attempts approx. are necessary to trigger the bug with that g-code?
from ender3v2s1.
I get the error intermittently. It doesn't matter which g-code, it's the same with all of them. Taking out the sd card and inserting it doesn't help, only turning off the printer for more than 20s.
from ender3v2s1.
Thanks for the report, how many attempts approx. are necessary to trigger the bug with that g-code?
It normally happens right when turning on the printer, and then will continue for ~15 more times. Then just fix it's self and load.
from ender3v2s1.
I tried the same G-code with a 4.2.2 board (at least 20 times) without issue, so, it is specific to S1 F4 boards. It could also be a problem with certain SD cards and the board's controller.
from ender3v2s1.
this isn't specific to anything initially. its more prevalent in chips having 256k because it seems the thumbnail image cache isnt being cleared once exited.
for reference:
classicrocker883#64
I was able to fix over on my end.
from ender3v2s1.
this isn't specific to anything initially. its more prevalent in chips having 256k because it seems the thumbnail image cache isnt being cleared once exited. for reference: classicrocker883#64
I was able to fix over on my end.
That's a different issue related only to the SDcard management, in the official ProUI the image is read in little chunks so the memory is never filled.
from ender3v2s1.
Sorry I am just getting back to this.
I tried with a few different SD cards (the card that came with the printer, SanDisk, PNY) and they all have the same problem. I have noticed that if you change the filament before trying to open a file, it works on the first attempt. I don't know if it has something to do with just waiting, or if a different operation cleans something up.
from ender3v2s1.
Sorry I am just getting back to this.
Check that you have the latest firmware version: Control / Info / Build date
from ender3v2s1.
Sorry I am just getting back to this.
Check that you have the latest firmware version: Control / Info / Build date
I am still running 2.1.3 20240127 - 14:17
. I got the firmware from the Linear Advance release https://github.com/mriscoc/Special_Configurations/releases/tag/LinearAdvance
from ender3v2s1.
This issue has had no activity in the last 60 days. Please add a reply if you want to keep this issue active, otherwise it will be automatically closed within 10 days.
from ender3v2s1.
I am still running having this issue
from ender3v2s1.
This issue has had no activity in the last 60 days. Please add a reply if you want to keep this issue active, otherwise it will be automatically closed within 10 days.
from ender3v2s1.
Related Issues (20)
- [BUG] Try to Auto Mesh Bed level with G29 HOT 3
- [BUG] Screen brightness going down somethimes when increasing value HOT 4
- [BUG] Numbers in auto leveling not shown unless bed tramming wizard is run first (TJC) HOT 20
- [Issue] Low bed heater PWM frequency powersupply noise HOT 7
- [BUG] Tramming Wizard won't go to all 4 corners and Autobuild Mesh is not moving correctly HOT 10
- Auto mesh isn't working HOT 3
- Probe stowed during mesh levelling, Z-Axis still goes down HOT 3
- Z Wizard not working properly - Final print setting way too high. HOT 9
- G92 doesn't behave preserve physical limits and physical mesh offsets HOT 3
- [BUG] (Tramming Wizard probing extremes) HOT 1
- mi impresora no reconose el firmware HOT 2
- Still problems with 300C update HOT 2
- [BUG] Unsupported custom configuration: Ender3 Pro, E3 free-runs, CR10DSPLY and Ultipanel PROUI extension HOT 13
- [BUG] Pause (M25) parks twice HOT 2
- [FEATURE REQUEST] SD card sorting most recent first HOT 3
- [BUG] (bug summary) HOT 5
- [BUG?] Rotating control became rather unpredictable in latest versions HOT 3
- Cura 5.8.0 doesn't have Display Filename and Progress on LCD plugins as indicated in the calibration guides HOT 1
- Printer killed - probbing HOT 3
- [BUG] M220 in gcode does not change feedrate HOT 2
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ender3v2s1.