Comments (10)
Here are links to videos of what it is doing. Sorry, tried to upload directly but I guess they are too big.
It seems like auto mesh build doesn't something different each time but you see the issue.
Tramming wizard is the same. Although this morning the points it is using seem to be in a smaller area. I verified the bed physical settings and maximized and centered the area and rebooted the printer. Maybe it is just because I was looking through my phone...
https://drive.google.com/file/d/1USW2UoyXjTuOXwSie6DhJ3Gd_0xFzTxw/view?usp=sharing
https://drive.google.com/file/d/1UMwLYo4TbRjAwN25KAU1wOF-IiUeZZWY/view?usp=sharing
Thanks!
from ender3v2s1.
The only thing that seems to remotely make sense to me might be a bad system board (v4.2.7 silent). I do have a new one on the way but won't be here until Monday according to tracking. I think I can reconcile issues on the board presenting this way (maybe bad electronic component, chip or memory). I would think if there was a broken wire or bad motor that nothing would work but so far I can still print on it just fine.
from ender3v2s1.
Today I update my extruder from bowden to Direct drive and change physical max and min x and y values. After that I run trimming wizzard with same result as you. I go to physical settings and change bad size to maximum and trimming wizzart start working.
from ender3v2s1.
So you increased the bed size and that made it work again?
from ender3v2s1.
Yes.
from ender3v2s1.
Hi, this is not a general printer support forum. Many problems can be easily solved by reading the firmware Wiki please check the calibration guide.
This Issue Queue is for firmware bug reports and development-related issues, and we prefer not to handle user-support questions here. For best results getting help with configuration and troubleshooting, please use the following resources:
Enhanced support in Patreon: https://www.patreon.com/mriscoc
Free community support:
- Github discussions: https://github.com/mriscoc/Ender3V2S1/discussions
- Facebook: https://www.facebook.com/groups/professionalfirmware
- Telegram: https://t.me/ender3v2s1firmware
- Reddit: https://www.reddit.com/r/Ender3v2Firmware
- Discord: https://discord.gg/3dprinters
from ender3v2s1.
Sorry mriscoc. I subscribed to the patreon and will continue there.
from ender3v2s1.
https://drive.google.com/file/d/1UMwLYo4TbRjAwN25KAU1wOF-IiUeZZWY/view?usp=sharing
Thanks, If you have a CRTouch, please disable HS mode.
from ender3v2s1.
I did try that as well after reading about CRTouch having some incompatibility.
from ender3v2s1.
Related Issues (20)
- [BUG] Printer occasionally restarts after selecting gcode with thumbnail HOT 12
- [BUG] UBL not compensating while print first layer. HOT 2
- X and Y Endstops are inverted in SKR Mini E3 V3 HOT 2
- No led control menu newest firmware HOT 3
- [BUG] M600 resumes mid air Ender 3V2 HOT 7
- [BUG] Cleaning/prime the nozzle off the table HOT 4
- [BUG] (f4 chip in ender 3 s1 is not flashing onto ender 3 s1 when put into printer) HOT 4
- [BUG] Ender3S1 Reboots and loses setting when SD card is inserted HOT 3
- Firmware Randomly Stops Printing HOT 3
- [BUG] build fails with missing binary operator before token HOT 4
- not able to compile SKR mini3 v3 with BLT UBL AND NP HOT 5
- [BUG] Try to Auto Mesh Bed level with G29 HOT 3
- [BUG] Screen brightness going down somethimes when increasing value HOT 3
- [BUG] Numbers in auto leveling not shown unless bed tramming wizard is run first (TJC) HOT 12
- [Issue] Low bed heater PWM frequency powersupply noise HOT 6
- Auto mesh isn't working HOT 2
- Probe stowed during mesh levelling, Z-Axis still goes down HOT 3
- Z Wizard not working properly - Final print setting way too high. HOT 3
- G92 doesn't behave preserve physical limits and physical mesh offsets HOT 2
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ender3v2s1.